Nilfisk-Advance CR 1500 Скачать руководство пользователя страница 90

Страница: 90 / 147

195

Service Manual – Advance 7765 / Nilfisk CR1500

Squeegee System

Functional Description

Overview

The squeegee system includes the rear squeegee assembly, swing squeegee support, squeegee lift assembly,

squeegee deck cylinder and the associated solenoid valves. The rear squeegee assembly is mounted at the

bottom rear of the machine and picks up the water from the floor. Two squeegees (inner and outer) pick

up the wastewater and direct it into the vacuum hoses which carry the wastewater to the recovery tank.

The squeegee deck cylinder lowers the squeegee assembly to the floor for normal scrubbing, and raises the

squeegee when the machine is not scrubbing or is moving in reverse.

Rear Squeegee Assembly

The

Squeegee Clamp Strap

on the

rear squeegee assembly holds the

Inner

and

Outer Squeegees

and

Squeegee Spacers

on the

Squeegee

Weldment

The two inner

Squeegee Knobs

fasten the

Squeegee Inlet Duct

and

Squeegee Spacers

to the

Squeegee

Weldment

, and hold the

Squeegee

Weldment

to the squeegee support

weldment.

The two outer

Squeegee Knobs

hold the

Squeegee Weldment

to the

squeegee support weldment.

Squeegee

Knob (4)

Squeegee

Weldment

Inner

Squeegee

Spacer (2)

Squeegee

Inlet Duct

Outer

Squeegee

Clamp Strap

Содержание CR 1500




















































































































































Результаты поиска

Содержание CR 1500

Отзывы:

Бренды по названию

Популярные бренды

Nilfisk-Advance CR 1500, Руководство по обслуживанию

Результаты поиска

Содержание CR 1500

Отзывы:

Бренды по названию

Популярные бренды