manualshive.com logo in svg

Nilfisk-Advance CR 1500, Руководство по обслуживанию

Поделиться
Скачать
Nilfisk-Advance CR 1500 Скачать руководство пользователя страница 88

Solution System

193

Service Manual – Advance 7765 / Nilfisk CR1500

Problem

Cause

Correction

No solution being 

transferred from the 

recovery tank to the 

solution tank (ESP/

Recycle option 

only).

Recycling System ON/OFF 

switch is set to OFF.

Set the Recycling System ON/OFF switch to ON.

Solution inlet filter dirty or 

plugged.

Clean or replace the filter.

ESP solution pump not 

operating.

Check the pump and wiring and repair/replace as 

necessary.

No voltage from the 

Recycling System ON/OFF 

switch to the ESP solution 

pump.

•  Check for voltage from wire #41 on the High 

Recovery Warning Light to the Recycling System 

ON/OFF switch. Repair or replace the wiring as 

necessary.

•  Check the Recycling System ON/OFF switch and 

wiring and repair/replace as necessary.

No detergent being 

delivered to the 

solution (ESP/

Recycle option 

only).

Recycling System ON/OFF 

switch is set to OFF.

Set the Recycling System ON/OFF switch to ON.

Detergent Flow knob is set 

to OFF.

Turn the Detergent Flow knob clockwise from the 

OFF position.

Detergent tank is empty. 

Check the detergent tank and refill as necessary.

Detergent supply lines are 

clogged.

Check the detergent lines and clean/replace as 

necessary.

Detergent pump not 

operating.

•  Check the Recycling System ON/OFF switch and 

wiring and repair as necessary.

•  Check the Detergent Flow rheostat and wiring to 

the detergent pump and repair as necessary.

•  Check the detergent pump. Replace if necessary.

No solution flow 

through the Power 

Spray Wand 

(optional).

Plugged solution feed hose.

Check and clean the solution feed hose as 

necessary.

Water pump not operating.

•  Check the On-Off toggle switch and wiring and 

repair as necessary.

•  Check the water pump. Replace if necessary.

Solution valve on the wand 

assembly not operating 

correctly.

Check the valve and repair/replace as necessary.

Содержание CR 1500




















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды