background image

Whirlamatic

  Operator Manual - 5

Replace the plug if the grounding pin is damaged or broken.

The green (or green/yellow) wire in the cord is the grounding wire. When replacing a plug, this wire
must be attached to the grounding pin only.

Extension cords connected to this machine should be 12 gauge, three-wire cords with three-prong
plugs and outlets. Do not use extension cords more than 50 feet (15 m) long.

GROUNDING INSTRUCTIONS

WARNING!

This machine must be properly grounded to protect the operator from electrical shock. Read the safety
instructions below before operating this machine.

GROUNDED

OUTLET BOX

120 VOLT PLUG

GROUNDING PIN

THREE-PRONG

 GROUNDED OUTLET

GROUNDING

TAB

120 VOLT PLUG

GROUNDED
OUTLET BOX

METAL
SCREW

TWO-PRONG
OUTLET

120 volt machines have this kind of three-prong
plug at the end of a three-wire electrical cord.
The grounding pin on this plug grounds the
machine when it is plugged into a three-prong
outlet.

A grounding adapter must be installed
as shown here if only two-prong out-
lets are available. The outlet box
must be grounded and the grounding
tab (or wire) on the adapter must be
installed under the head of the screw
in the center of the outlet cover.
Grounding adapters for 120 volt plugs
are available at most hardware stores.

Grounding adapters are not approved
for use in Canada.

https://harrissupplyind.com - To Order Parts Call 608-268-8080

Содержание 56183100













Отзывы: