background image

Manual: TIRF Microscope

 

Ee-1454

 

 

Martijn de Gruiter 

 

Erasmus OIC 

3

 

Start system 

 

Turn on the power by the power socket (on the floor under the table) 

 

Switch the mercury lamp on and then ignite it. 

o

 

If not needed don’t turn the mercury lamp on 

o

 

The unit on the shelf closest to the door 

 

Turn on all devices with a button on the shelf and the table. 

o

 

Camera and laser box are automatically enabled  

 

Next turn on the device with a key: Laser control panel 

 

Start the computer and start the program Metamorph. 

o

 

Select suited user account. 

 

Live Cell imaging: 

 

When imaging at 37

o

C: 

 

The heating device to maintain your cells uses water. 

o

 

fill reservoir with demineralized water up to level of CO2 tube 

 

Allow the system to warm up for 15-30 minutes 

 

Settings for the heating unit are paper on the wall, choose your settings 

o

 

General settings for cells on a coverslip: 

o

 

top heater 40.5 ° C 

o

 

bath heater 38.5 ° C 

o

 

stage heater 38.5 ° C 

o

 

lens heater 37 ° C 

 

 

 

Ensure that the cells are grown on a glass coverslip  

 

Place the slide in the metal ring, tighten firmly but not too hard because it will break the 

glass 

 

Add 1-2 ml of the medium from the appropriate well. There is a convex surface 

 

Move with a paper towel around the edge of the coverslip from below with a little pressure, 

if no medium leaks from the ring your seal is good. 

 

Wipe clean the underside of the slide with ethanol to prevent contamination of the 

objective and microscope 

 

 

Содержание Eclipse Ti TIFT 1454










Отзывы: