Nice M3BAR, Инструкции и предупреждения по установке и использованию

Страница: 7 / 48

English – 5
EN
3.4 - Barrier lift fixture
3.4.1 - If the support surface already exists
01. Open the cabinet of the barrier ( fig. 13 );
02. Place the barrier on the fixing surface and trace the points where the slots
are to be fixed (
fig. 14 );
03. Move the barrier and drill the traced surface points; then insert 4 expansion
bolts, not supplied (
fig. 15 );
04. Position the barrier correctly and secure by means of the relative nuts and
washers not supplied (
fig. 16 ).
3.4.2 - If the support surface does not exist
01. Dig the foundation pit ( * ) to house the foundation plate;
02. Prepare ducting for connection cables ( fig. 17 );
03. On the foundation plate, fix the 4 bolts, placing a nut on the upper side of
each and one on the lower side of the plate (
fig. 17 ). Caution – The lower
nut must be tightened down to the threaded section;
04. Now cast the concrete, and before it sets, embed the foundation plate,
which must be positioned flush with the surface, parallel to the pole and
perfectly level (
fig. 17 ). Wait for the concrete to set completely; in general,
at least 2 weeks;
05. Remove the 4 upper nuts of the bolts;
06. Open the cabinet of the barrier ( fig. 18 );
07. Position the barrier correctly and secure it by means of the relative nuts
and washers supplied with the foundation plate and removed in point 04
(
fig. 19 ).
( * ) Note - The fixing surface must be perfectly smooth and flat. If the surface is
in concrete, it must be at least 0.15 m thick, and must be adequately reinforced
with steel cages. The concrete volume must be greater than 0.2 m
3 (a thick-
ness of 0.25 m corresponds to 0.8 m 2 ; in other words equal to a square base
of approx. 0.9 m per side). Anchoring to the concrete can be by means of 4
expansion bolts, fitted with 12 MA screws, which resist to a traction load of at
least 400 Kg. If the fixing surface is in another material, the consistency must be
checked and ensure that the 4 anchoring points can resist a load of at least
1000 Kg. For fixture, use 12 MA screws.
3.5 - Pole installation
3.5.1 - Pole support assembly
01. Insert the two plugs in the relative seats on the output motor shaft ( fig. 20 );
02. Position the support on the output motor shaft, placing it in the “vertical
pole” position and tighten the relative screws and washers fully down to
secure (
fig. 21 );
03. Position the pole cover and partially secure by means of the 6 screws sup-
plied (
fig. 22 ).
3.5.2 - Pole assembly (3 metres / 5 metres)
01. Assemble the two pole insertions ( fig. 23 );
02. Insert, from the same end of the pole, the insertions just assembled. Use a
rubber mallet (
fig. 24 );
03. Lightly grease the aluminium guide on both sides ( fig. 25 );
08. Perform this operation on both ends of the pole: insert the first part of impact
protection rubber in the slot, through to the end of the pole; then insert the
joint for the impact protection rubber (
fig. 26 ) and repeat with all parts;
09. The impact protection rubber may protrude by about 1 cm from the end of
the profile (
fig. 27 ):
A) position the pole plug and lock it with the two screws ( fig. 28 );
B) position and block the two rubber cover plugs ( fig. 28 );
10. Insert the pole assembly in the pole support shell, pushing it up to the end
and then tighten the 6 previously inserted support screws fully down (
fig. 29 ).
TABLE 4
LENGTH OF THE POLE
M3BAR M5BAR M7BAR LBAR
2,65 m 3,15 m 3,5 m 4,15 m 5,15 m 5,15 m 5 m, 6,33 m 7,33 m 7,33 m 8,33 m 9,33 m
entire entire with joint
ACCESSORIES
XBA13 - Rubber A1 A3 0 0 C2 0 0 0 B2 0 0 B1
XBA4/XBA6/XBA18 - Lights A1 A3 1 1 C2 1 1 1 B2 1 1 B1
WA13 - Rack - - 1 1 - 2 1 1 - 2 2 -
WA12 - Mobile support - - 5 4 - 4 3 3 - 3 3 -
XBA11 - Pivot Pole B3 B3 C1 C3 - - - - - - - -
POSITION OF THE SPRING ANCHORING HOLE
0÷1 = B2 0÷1 = B3 0÷2 = A2 0÷2 = B1 0÷2 = A1 0÷2 = A3
2÷7 = B3 2÷4 = C1 3÷5 = A2 3÷5 = B2 3÷4 = A2 3÷6 = B1
5÷6 = C2 6÷7 = A3 5÷6 = A3
Example:
M5BAR with 4m pole + Rack
(1piece) (value:1) + Pole lights
(value:1) =
Sum of values: 2
Risult = POSITION C1
A
M3BAR / M5BAR M7BAR / LBAR
1 2 3
B
C
1 2 3
A
B