Nice HOPP HO7124, Инструкция по эксплуатации

Страница: 24 / 36

24 – ENGLISH
9.1.4 Learning of other devices
Normally the learning of devices connected to “ BlueBUS ” and
the “ STOP ” input takes place during the installation stage; how-
ever, if new devices are added or old ones removed, the learn-
ing process can be redone.
FLASH
EL
ST
OP
SBS
OPEN
BLUEBUS
L1
L2
43
To do this:
1. simultaneously press and hold the [Open
p
] and [Stop/
Set] buttons
2. release the buttons when LEDs “ L1 ” and “ L2 ” start flash-
ing rapidly (after roughly 3 seconds)
3. wait a few seconds until the control unit has completed the
device learning phase
4. at the end of this phase, the “ Stop ” LED must be lit, LEDs
“ L1 ” and “ L2 ” must switch off, while LEDs “ L1…L8 ” will
switch on depending on the status of the ON-OFF func-
tions they represent.
m
After having added or removed devices, the auto-
mation test must be carried out again as specified
in the “Testing” paragraph.
9.2 CONNECTING AN OXI RADIO RECEIVER
The control unit has a slot for mounting an OXI radio receiver
(version with antenna connector mounted), which can be used
to remotely control the control unit through transmitters that in-
tervene on the unit’s inputs.
To install a receiver (“ Figure 44 ”):
1. remove the cover ( A )
1. insert the receiver ( B ) in the appropriate slot ( C ) on the
control unit.
A
B
C
44
The association between the radio receiver output and the com-
mand executed by the motor is shown in “ Table 11 ”:
Table 11
OXI IN MODE I OR MODE II
Receiver output Command
Output No. 1 “Step-by-Step”
Output No. 2 “Partial opening 1”
Output No. 3 “Open”
Output No. 4 “Close”
If the OXI radio receiver used in “EXTENDED MODE” is installed,
it may send the commands shown in “ Table 12 “.
Table 12
OXI IN EXTENDED MODE II
No. Command Description
1 Step-by-Step “SbS” (Step-by-Step) command
2 Partial opening 1 “Partial opening 1” command
3 Open “Open” command
4 Close “Close” command
5 Stop Stops the manoeuvre
6
Condominium
Step-by-Step
Command in condominium mode
7
High priority Step-
by-Step
Commands also with the automation
locked or the commands enabled
8 Partial open 2
Partial opening (the M2 gate leaf
opens to 1/2 the full length)
9 Partial open 3
Partial open (the two gate leaves
open to 1/2 the full length)
10
Opens and locks
the automation
Triggers an opening manoeuvre
and, once this terminates, locks the
automation; the control unit will not
accept any command other than
“High priority Step-by-Step” and
automation “Unlock”, or (only from
Oview) the following commands:
“Unlock and close” and “Unlock and
open”
11
Closes and locks
the automation
Triggers a closing manoeuvre and,
once this terminates, locks the
automation; the control unit will not
accept any command other than
“High priority Step-by-Step” and
automation “Unlock”, or (only from
Oview) the following commands:
“Unlock and close” and “Unlock and
open”
12 Lock automation
Triggers the stoppage of the
manoeuvre and locks the
automation; the control unit will not
accept any command other than
“High priority Step-by-Step” and
automation “Unlock”, or (only from
Oview) the following commands:
“Unlock and close” and “Unlock and
open”
13
Release
automation
Triggers unlocking of the automation
and restores normal operation
14
On Timer
Courtesy light
The courtesy light output switches on
with timer-based switching off
15
On-Off
Courtesy light
The courtesy light output switches on
and off in Step-by-step mode
l
For further information, consult the specific manual
of the receiver.