A.6 - Memorising ANOTHER TRANSMITTER (second, third, etc.)
NOTES AND WARNINGS
• To run procedures A.6.1.
A
and A.6.2.
A
, you must have a
new transmitter
to memorise and an
old
previously memorised transmitter. The two transmitters must
have the “PRG” and “ESC” buttons (like “ERA P” and “ERA W” transmitters).
•
To run procedures A.6.1.
B
and A.6.2.
B
you must have a
new
transmitter to memorise, chosen from the “Nice Screen” catalogue , and an
old
previously memo-
rised transmitter.
A.6.1 - To memorise the transmitter buttons in “Mode I” (“Standard mode”)
• Procedures A.6.1
A
and A.6.1.
B
memorise all the
new
transmitter’s buttons in “Mode I”, with the same configuration as the
old
transmitter (for details about “Mode
I” see par. 4.4.1-A).
A.6.1.
A
- Procedure for transmitters equipped with the “PRG” and “ESC” buttons (“ERA P” and “ERA W”)
1
2
OLD
PRG
...
2
1
sec.
2
PRG
On the OLD transmitter:
hold down the
button and
wait ...
count 2 movements;
wait
again...
count 2 more move-
ments;
release the button.
A
A.5 - Programming an INTERMEDIATE POSITION (position “H”)
NOTES AND WARNINGS
•
This procedure memorises an intermediate position (position “H”) between the Up (“0”) and Down (“1”) limit switch positions. When the automation is being used,
after giving the
intermediate position
command, the system will automatically stop the awning at the programmed “H” position.
• You can memorise up to 30 “H” positions wherever you wish, provided that these are between the two limit switch positions. These positions can only be pro-
grammed after the limit switch positions. Repeat this procedure for each position you wish to memorise.
• The first “H” position must be programmed using the buttons
s
+
t
,
on the transmitter used to run the procedure itself
. However, each subsequent position
“H” must be programmed using a button
on another non-memorised transmitter
.
• To change an existing “H” position, move the awning to the desired height and run this procedure; in
step 06
, however, press the button associated with the ex-
isting “H” position you are changing.
1
2
3
4
“
H
”
(x
1
)
PRG
2
=
5
sec
2
Move the awning to the
desired “
H
” position.
Press and release
the button (
1 time
);
count 2 movements.
Hold down both buttons...
release them after
5 sec-
onds
;
count 2 movements.
4
5
6
...
Precisely ad-
justing the
“H” posi-
tion
“
H
”
=
5
sec
3
Select one of the following potions
and execute it:
• option A
– to memorise the
FIRST “H” position.
• option B
– to memorise a SUP-
PLEMENTARY “H” position.
Press the buttons until you reach the desired position.
Alternatively
, for more accurate adjustment, run pro-
cedure B.1.
Hold down the but-
ton and
release it after
5 sec-
onds
;
count 3 movements.
option –
A
6
end
option –
B
6
end
=
5
sec
4
=
5
sec
...
...
4
Hold down both but-
tons...
release them
after
5 sec-
onds
;
count 4 movements.
On ANOTHER transmitter,
which has NOT been memo-
rised:
hold down any button
you wish;
release it after
5 seconds
;
count 4 movements.
A
9
– English
Содержание E Fit M 720
