manualshive.com logo in svg

Nice Apollo CBOX1K, Руководство пользователя

Поделиться
Скачать
Nice Apollo CBOX1K Скачать руководство пользователя страница 15

15

Tighten the wire terminals to complete the wiring connection 
to the T5/T7. Re-attach the cover and secure with the 
provided Phillips-head screws.

orange

gr

een

white

blue

yellow

re

d

black

Connect T5 motor 

cable to outlined 

wire terminals

white

gr

een

orange

blue

yellow

re

d

black

Connect motor 

cable to outlined 

wire terminals

T5 MOTOR WIRING

T7 MOTOR WIRING

1

2

3

4

5

1

2

3

Connect the T5/T7 cable to the 5-pin connector as shown 

below for 

pull to open installations

Connect the actuator motor leads to the 3-pin connector 
as shown below. 

Note: If the gate moves in the opposite 

direction from what is expected, reverse the actuator 
wiring from what is shown. (Red to Pin 3, Black to Pin 1).

Install the 5 and 3-pin connector for motor 1 into the 

connection labeled “Motor 1” on the controller as shown. 
For a dual gate installation install the 5 and 3-pin and 

connector for motor 2 into the connection labeled “Motor 2”.

Note:

 (Motor 1) - Make sure motor lead connector is plugged 

in below the limit 5 pin terminal connector

T5 and T7

Limit and 

Encoder wiring

T5 and T7

Motor wiring

green

yellow

blue

orange

white

red

black

green:  limit common

yellow: motor encoder signal

blue: common

orange: open limit switch

white:  close limit switch

MOTOR 2

MOTOR 1

8.7 - ACTUATOR WIRING

8.8 - LIMIT AND MOTOR CONNECTION TO THE BOARD

Connect the T5/T7 cable to the 5-pin connector as shown 

below for 

push to open installations.

Connect the T5/T7 motor leads to the 3-pin connector as 

shown below. 

Note: If the gate moves in the opposite direc-

tion from what is expected, reverse the motor wiring from 

what is shown. (Red to Pin 1, Black to Pin 3). 

1

2

3

4

5

1

2

3

T5, T7

H12, M12

Limits and 

Encoder

T5, T7

H12, M12

Motor Leads

White: Close limit
Orange: Open Limit
Green: Limit Common
Yellow: Encoder Signal
Blue: Encoder Power

NOTE: If gate moves in opposite 
direction from what is expected, 
reverse the motor power lead wiring

Green

Yellow

Blue

White

Orange

Black

Red

NT

-T51K & NT

-T71K INST

ALLA

TION

Содержание CBOX1K

















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды