background image

2

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, 

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

WARNING: THIS APPARATUS MUST BE EARTHED.

The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of sufficient magnitude to constitute a risk
of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.

Marking by the "CE" symbol (shown left) indicates compliance of this device with
the EMC (Electromagnetic Compatibility) and LVD (Low Voltage Directive)
standards of the European Community.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause interference to radio or television reception, which can be deter-
mined by turning the equipment on and off, the user is encouraged to try to correct the interference by
one or more of the following measures:

·

Reorient or relocate the receiving antenna;

·

Increase the separation between the equipment and the receiver;

·

Connect the equipment into an outlet on a circuit different from that to which the receiver is    

connected;

·

Consult the dealer or an experienced radio/TV technician for help.

Содержание Power2














Отзывы: