NEXT pool ABRIBLUE IMM'Ax, Руководство по установке

Страница: 28 / 44

Installa ti on instruc ti ons for the IMM'Ax automa ti c immersed safety cover - 28/36
28
7. Accessories and op ti ons
7.1 Fi tti ng an an ti -bending console
Fig. 67
- Plan a concrete belt using a 350 Kg cement per m 3 concrete
mix with a size of w 25 cm x h 40 cm x l 100 cm using at least
0.10 m
3 to stabilise the fi xture of the an ti -bending console.
- Place the an ti -bending console on the edge and against the
rear wall of the pool.
- Mark the edges.
- Install the arm (1) horizontally by correctly placing the
ver ti cal part of the bracket (2) against the pool wall (3).
- Install the wedges under the horizontal plate if there is a
liner a tt achment rail for example, or behind the ver ti cal
support to deliberately give an angle to the console in order
to obtain a horizontal beam once the duckboard walkway
is in place.
- A more accurate adjustment of the beam height is carried
out using the bracket's oblong holes (4) and must maintain
the bo
tt om of the suppor ti ng brackets 4 cm above the
water line.
7.2 Fixture on the edges
7.2.1 Fixing the fl anges to the edge.
Fig. 68
- Assemble the stainless steel fi xing plate with the cover
using the M10 nuts and washers.
- Use the stainless steel supports as a template to mark
the posi ti on of the 4 fi xing holes on each side of the pool
(they must be carried out as close as possible to the pool
depending on the structure's reinforcement elements)
- Drill 12 mm diameter holes at a depth of 70 mm.
- Manually screw the brass plugs to the TFHC M10x60
screws through the stainless steel plate.
- Hammer the heads of the TFHC M10x60 screws using
a mallet in order to insert them into the concrete belt.
- Tighten and check that the fi xtures hold.
- If necessary used the supplied wedges to ensure that
the edge plates are horizontal.
7.2.2 Fixing the sliders to the edge
Fig. 69
- Assemble the stainless steel fi xing plate to the slider using
the stainless steel studs on the top part of the slider.
- Use the stainless steel supports as a template to mark
the posi ti on of the 2 fi xing holes on each side of the
pool.
- Drill 10 mm diameter holes at a minimum depth of 60
mm.
- Manually screw the brass plugs to the TFHC M8x55
screws through the stainless steel plate.
- Strike the heads of the TFHC M8x55 screws using a
mallet in order to insert them into the concrete belt.
- Tighten and check that the fi xtures hold.
- The beam box is fi tt ed to the slider using M8 nuts.
7.2.3 Fixing the beam boxes to the edges
- Make sure that the height adjustment of the bo tt om of the
duckboard corresponds to your needs.
- The fi xture to the edge of the 120 mm beam makes it
possible to place this face 11 mm above the edge and
up to - 8 mm.
- The fi xture to the edge of the 80 mm beam makes it
possible to place this face 5 mm above the edge and up
to - 13 mm.
- Assemble the stainless steel fi xing plate to the ver ti cal
beam box support using the stainless steel studs in the
upper part of the ver
ti cal support.
- Use the stainless steel supports as a template for step
3.2.5 of the assembly and marking.
- Make two fi xtures on each side.
7.3 Chemical sealing with inserts
- For M8 screws, drill to a diameter of 14 mm and depth of
65 mm,
- For M10 screws, drill to a diameter of 20 mm and depth of
70 mm,
- Clean the holes by blowing.
- Inject a dose of chemical sealer and place the insert,
- Respect the drying ti me indicated on the cartridge.
Fig. 67
1
2
3
4
Fig. 68
Fig. 69