Nexo GEO M12 Series Скачать руководство пользователя страница 35

Страница: 35 / 90

GEO

M12

HARDWARE

SETUP

PROCEDURE

Page 35/90

6.3.3 GEO M12 only on Touring Bumper with stacking extensions

Required item

1 x VNT-BUMPM12

1 x VNT-GSTKM10M12S

1 x VNT-GSTKM10M12L

IMPORTANT

Ground stack assembly VNT-B VNT-GSTKM VNT-GSTKM10M12L is
rated for a maximum of 6 x GEO M12 in any inter cabinet angle configuration with +/-12°
initial angle, provided this device is assembled according to below rules:

VNT-BUMPM12 must be adjusted to be horizontal

Public is not allowed within a safety area which radius is equal or higher than
assembly height.

It is highly recommended to secure the system to a fix point located at the back of the
stack.

Procedure

Set the bumper on the ground so that front with front direction indicated by side arrows

Insert VNT-GSTKM10M12L and/or VNT-GSTKM10M12S guides into bumper front and rear center
slots

IMPORTANT

If bottom GEO M102 angle is negative, VNT-GSTKM10M12L must be connected at the
front and VNT-GSTKM10M12S at the back

If bottom GEO M12 angle is positive, VNT-GSTKM10M12S must be connected at the
front and VNT-GSTKM10M12L at the back

Lock VNT-GSTKM10M12L and/or VNT-GSTKM10M12S into bumper with VNT-BUMPM12 quick
release pin 1240.

Содержание GEO M12 Series



























































































Результаты поиска

Содержание GEO M12 Series

Отзывы:

Бренды по названию

Популярные бренды

Nexo GEO M12 Series, Системное руководство

Результаты поиска

Содержание GEO M12 Series

Отзывы:

Бренды по названию

Популярные бренды