Nexo GEO M12 Series Скачать руководство пользователя страница 32

Страница: 32 / 90

Page 32/90

GEO

M12

HARDWARE

SETUP

PROCEDURE

6.3.2 GEO M12 only on Lightweight Bumper

Required item

1 x GMT-LBUMPM12

IMPORTANT

GMT-LBUMPM12 is rated for a maximum of 3 stacked GEO M12 in any inter cabinet
angle configuration with 0/+3° initial angle, provided the stack is assembled according
to below rules:

- GMT-LBUMPM12 must always be installed on a horizontal surface

- Public is not allowed within a safety area which radius is equal or higher than assembly
height.

Procedure

GMT-LBUMPM12 can be flipped front and back depending if it connects to GEO M12 Right or Left.

When connecting GEO M12

Left, bumper front is on the “G” hole index side

When connection GEO M12

Right, bumper front is on the “A” hole index side

GEO M12 Left

t the bumper on the ground so that front is on the “G” hole side

Remove the BL825 quick release pin of rear GMT-LBUMPM12 link bar, and rotate it upwards

Release first GEO M12 link bar, and set AutoRig in automatic lock position

Position first GEO M12 on top of the bumper, front points will lock automatically

Connect the bumper link bar (selection of 0° / +3°) to GEO M12 rear rigging plate (hole marked
“bumper”) Lock with the quick release pin BL0825.

IMPORTANT

Ensure that all AutoRig

systems are locked

Содержание GEO M12 Series



























































































Результаты поиска

Содержание GEO M12 Series

Отзывы:

Бренды по названию

Популярные бренды

Nexo GEO M12 Series, Системное руководство

Результаты поиска

Содержание GEO M12 Series

Отзывы:

Бренды по названию

Популярные бренды