manualshive.com logo in svg

Nexcom NDiS V1100, Руководство пользователя

Поделиться
Скачать
Nexcom NDiS V1100 Скачать руководство пользователя страница 57

Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved.

43

NDiS V1100 User Manual 

Chapter 4: BIOS Setup

Enable Hibernation

Enables or disables system ability to Hibernate (OS/S4 Sleep State). This

option may not be effective with some operating systems.

ACPI Sleep State

Select the highest ACPI sleep state the system will enter when the suspend

button is pressed.

Advanced

Version 2.22.1282 Copyright (C) 2022 AMI

Aptio Setup - AMI

→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit

Enable or Disables System ability 
to Hibernate (OS/S4 Sleep State). 
This option may not be effective 
with some operating systems.

ACPI Settings

Enable Hibernation

ACPI Sleep State

[Enabled]

[S3 (Suspend to RAM)]

ACPI Settings

This section is used to configure ACPI settings.

NCT6126D Super IO Configuration

This section is used to configure the I/O functions supported by the onboard
Super I/O chip.

Super IO Chip

Displays the Super I/O chip used on the board.

Advanced

Version 2.22.1282. Copyright (C) 2022 AMI

Aptio Setup - AMI

→←: Select Screen
↑↓: Select Item
Enter: Select
+/-: Change Opt.
F1: General Help
F2: Previous Values
F3: Optimized Defaults
F4: Save & Exit
ESC: Exit

Set Parameters of Serial Port
1 (COMA)

NCT6126D Super IO Configuration

Super IO Chip

Serial Port 1 Configuration

Serial Port 2 Configuration

NCT6126D

Содержание NDiS V1100






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды