Nexans Euromold K480TB/G Скачать руководство пользователя страница 10

Страница: 10 / 10

CONNECTOR EARTHING

AND CABLE CLAMPING

system

earth

cable

clamp

screen

wires

Bend back the screen wires along the outer

sheath to form a pig tail.

Connect the earthing lead and screen wires to

the system earth.

NOTE :

A connector/bushing mated combination

should not be allowed to carry the full

weight of the cable.

Therefore clamp the cable as close as

possible to the connector.

IMPORTANT NOTES :

- Never disconnect the connector from energised equipment nor energise a disconnected connector

without previously installing on its appropriate corresponding mating part.

- Do not allow hydrocarbon oils or solvents to contaminate the E.P.D.M. rubber.

In the event of contamination, wipe the surface clean with a dry cloth.

earthing

lead

Nexans Network Solutions NV - div. EUROMOLD

Zuid III - Industrielaan 12

B-9320 EREMBODEGEM-AALST – BELGIUM

Tel: +32 (0)53/85 02 11 – Telefax: +32 (0)53/83 10 13

[email protected]

INSTALLATION OF THE CAP

protective

cap

locking

point

protective

cap

Installation on insulating plug BIPR without voltage

detection point :

- Clean the inside of the cap and the outside surface of

the connector and insulating plug.

- Place the nylon vent rod along the insulating plug (see fig.)

to exhaust the air during assembly of the cap.

- Push the cap

firmly

over the connector and onto the

insulating plug.

- Press the cap on all sides to make sure it is well positioned

over the connector. Position the cap with the pulling tab

pointing downwards.

- Remove the nylon vent rod.

Installation on insulating plug BIPA with voltage

detection point :

- Clean the inside of the cap and the outside surface of

the connector and insulating plug.

- Place the nylon vent rod along the insulating plug (see fig.)

to exhaust the air during assembly of the cap.

- Push the cap

firmly

over the connector and onto the

insulating plug.

Press the centre of the cap onto the locking point

until it snaps into place.

Press the cap on all sides to

make sure it is well positioned over the connector. Position

the cap with the pulling tab pointing downwards.

- Remove the nylon vent rod.

nylon vent rod

IS97179-ENG - K480TB/G

-CW45-

CA0 - Revision 3

Page 10 of 10

For

information

only

Содержание Euromold K480TB/G











Результаты поиска

Содержание Euromold K480TB/G

Отзывы:

Похожие инструкции для Euromold K480TB/G

Бренды по названию

Популярные бренды

Nexans Euromold K480TB/G, Руководство по установке

Результаты поиска

Содержание Euromold K480TB/G

Отзывы:

Похожие инструкции для Euromold K480TB/G

Бренды по названию

Популярные бренды