background image

Semi scale  model

BUILDING INSTRUCTIONS / MONTAGEANLEITUNG

SPECIFICATIONS

Wingspan                                           107 in.                                        
Length                                                78.7 in.
Flying weight                                     14.4 lbs
Gas Engine                                     26 ~ 30cc
Radio                             6 Channel / 8 servos                                             

Technische Daten

Spannweite                                      2.720mm
Länge                                               2.000mm
Fluggewicht                                      6.500g
Verbrennerantrieb                           26 ~ 30cc
Fernsteuerung                   6 Kanal / 8 Servos

WARNING!

 This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! 

Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

26 ~ 30cc

Gas Engine

Pilatus 

PC-6

Porter

RADIO CONTROL MODEL / RC FLUGMODELL

Содержание Pilatus Porter PC-6



















Отзывы: