Nexa DORNIER DO-27 Скачать руководство пользователя страница 4

Страница: 4 / 11

When you are satisfied with the alignment,
use a pencil to trace around the right and
left of the stabilizer where it meets the
fuselage.

Cut away only
the covering
both side

Realign the vertical stabilizer, then glue
the vertical stabilizer into the fuselage,
using a generous amount of thin CA.

Thin CA glue

Hinge

STABILIZER

Apply thin CA to both
side of the hinge

Push the rudder and its hinges into the hinge slots in the trailing edge of the
horizontal stabilizer. There should be a minimal hinge gap.
When satisfied with the and alignment, hinge the elevator to the horizontal stabilizer using CA glue.

WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !

Vergewissern Sie sich, sauber geklebt zu haben.
Andernfalls konnen Probleme mit der Flugeigenschaft
auftreten!

WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !

DORNIER DO-27

4-Vertical stabilizer

Содержание DORNIER DO-27












Результаты поиска

Содержание DORNIER DO-27

Отзывы:

Похожие инструкции для DORNIER DO-27

Бренды по названию

Популярные бренды

Nexa DORNIER DO-27, Инструкция по эксплуатации

Результаты поиска

Содержание DORNIER DO-27

Отзывы:

Похожие инструкции для DORNIER DO-27

Бренды по названию

Популярные бренды