Nexa DORNIER DO-27 Скачать руководство пользователя страница 3

Страница: 3 / 11

Note: The slots for the control horn
installation are pre- cut at factory.

Control horn

...........2

Thin CA glue

Push the elevator and its hinges into the hinge slots in the trailing edge of the
horizontal stabilizer.
There should be a minimal hinge gap.
When satisfied with the and alignment, hinge the elevator to the horizontal stabilizer using CA glue.

Hinge

STABILIZER

Apply thin CA to both
side of the hinge

Full the rudder out of the
vertical stabilizer.

WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !

Vergewissern Sie sich, sauber geklebt zu haben.
Andernfalls konnen Probleme mit der Flugeigenschaft
auftreten!

DORNIER DO-27

3-Vertical stabilizer

DORNIER DO-27

2-Horizontal stabilizer

Содержание DORNIER DO-27












Результаты поиска

Содержание DORNIER DO-27

Отзывы:

Похожие инструкции для DORNIER DO-27

Бренды по названию

Популярные бренды

Nexa DORNIER DO-27, Инструкция по эксплуатации

Результаты поиска

Содержание DORNIER DO-27

Отзывы:

Похожие инструкции для DORNIER DO-27

Бренды по названию

Популярные бренды