manualshive.com logo in svg

NEX ROBOTICS FIREBIRD V ATMEGA 2560, Руководство по оборудованию

Поделиться
Скачать
NEX ROBOTICS FIREBIRD V ATMEGA 2560 Скачать руководство пользователя страница 84

Fire Bird V ATMEGA2560 Hardware Manual

29

XCK1 / PD5 / GPIO (uC pin 48)

30

T5 / PL2 / GPIO (uC pin 37)

31

PG1 / GPIO (uC pin 52)

32

PG0 (uC pin 51)

33

T1 / PD6 / GPIO (uC pin 49)

34

T0 / PD7 (uC pin 50)

35

No Connections

36
37

TXD1 / INT3 / PD3: Connected to the MAX 202 for RS232 communication. Do not use 
for other purpose unless connection with MAX 202 is removed. (uC pin 46)

38

RXD1 / INT2 / PD2: Connected to the MAX 202 for RS232 communication. Do not use 
for other purpose unless connection with MAX 202 is removed. (uC pin 45)

39

PJ6 / GPIO (uC pin 69)***

40

PJ7 / GPIO (uC pin 79) ***

41

PJ4 / GPIO (uC pin 67) ***

42

PJ5 / GPIO (uC pin 68) ***

43

PJ2 / GPIO (uC pin 65) ***

44

PJ3 / GPIO (uC pin 66) ***

45

RXD3 / PJ0 / GPIO (uC pin 63)****

46

TXD3 / PJ1 / GPIO (uC pin 64)****

47

No Connections

48
49
50
51
52
53
54
55
56

Table 4.3: ATMEGA2560 microcontroller board expansion header table

Note:

* In order to use these pins as JTAG or as ADC for external sensor interfacing, remove all 4 
connectors   for   the   jumper   2   of   the   microcontroller   board.   When   jumpers   are   removed   IR 
Proximity sensor 1 to 4 will be disconnected from the robot.

**   Pins   can   be   used   as   SPI   bus.   These   pins   are   already   connected   to   slave   ATMEGA8 
microcontroller via J4 of the microcontroller board. Before using it as a SPI bus for external 
device interfacing, remove J4 to disconnect ATMEGA8 slave microcontroller or use different 
pin of the microcontroller as SS (slave select).

*** All the pins of the PORTJ are connected to the bargraph LED display. While using these 
pins as GPIO to turnoff this bargraph LED display, remove jumper J3 of the microcontroller 
board.

**** PJ0 and PJ1 can be used as GPIO as well as TXD and RXD for UART 3. These pins are 
also connected to bargraph LED display. While using these pins as UART 3, jumper J3 must be 
removed to disable bargraph LED display in order to avoid loading on the TXD and RXD lines 
of the device which is connected with the ATMEGA2560 microcontroller. 

© NEX Robotics Pvt. Ltd. and ERTS Lab, CSE, IIT Bombay, INDIA                                      84

Содержание FIREBIRD V ATMEGA 2560


























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды