background image

 

AeroVent

®

 Standard

 

ALWAYS wear appropriate personal protective equipment when operating the unit

!

 

 

 

AeroVent® Standard Manual / 4840.1117 

 

 

 

 

 

 

ASSEMBLY 

1)

 

Install front support foot that was removed for shipping. Screw all the way in 

2)

 

Remove the 2” bung

-fitting cap from an empty 30 or 55 gallon recovery 

drum. Insert the threaded nipple of the AeroVent® into the opening and 
turn the unit until hand tight.  One adjusting foot should be located just 
inside the chime.  The other should rest on top of the chime. 

3)

 

Turn the adjustable rear support foot clockwise until snug to the top of 
the drum.  Adjust front support foot tight to chime after adjusting rear 
foot.  

4)

 

Open lid and let it rest against back stop.  Remove 2 screws from lid 
handle.  Position handle on top of lid and install 2 screws from underside 
and tighten screws. 

5)

 

Place the operating handle on the mounting post. Insert one 5/16-

18 x 1” 

bolt through each handle and mounting post hole. Secure with one  
5/16-18 locking nut and washer on each bolt and snug nuts at this time. (Pic 1) 

6)

 

Place one of the Plunger Blocks into the hole on the closed lid assembly. 
Lower the handle and adjust the swivel foot so that it is centered in the 
plunger block.  

Completely tighten all nuts and bolts of the handle assembly to the 
mounting post at this time. (Pic 2)  

7)

 

Install can stop in slots at front of can tray. 

8)

 

Remove the 3/4” bung fitting cap from top of the recovery drum and 

thread the Safe2Filter filter housing into place. Hand-tighten only! 

9)

 

Attach the clamp end of the grounding cable to a suitable grounding 
source, such as a metal water pipe or grounding rod. 

 

Box should include these parts

:

 

 

 

AeroVent

®

 unit with ground cable 

 

#3-Operating Handle 

 

#14-Safe2Filter 

 

5/16-

18 x 3/4” Bolt (4)

 

 

¼” Flat Washers (4)

 

 

5/16-18 Locking Nuts (4) 

 

#7-Plunger Block Kit (3) 

 

Can Stop 

 

#5-Lid Handle 

 

Owner’s Manual 

 

Pic 1 

Operating 

Handle #3 

Plunger 

Block Kit #7 

Can Stop 

5/16-

18 x 3/4” Bolt (4)

  

¼” Flat Washers (4

5/16-18 Locking Nuts (4) 

Lid Handle 

#5 

Safe2Filter 

#14 

FIGURE 2

 

FIGURE 1

 

Front Support 

Foot 

Содержание Aerovent Standard










Отзывы: