New lift FST Скачать руководство пользователя страница 159 | Manualshive

Страница: 159 / 174

background image

6 Error List

6.4 Error messages

FST_HB.EN04/03

157

35

DOOR LOCK TIMEOUT

Door lock timeout is not long
enough.

The car door is closed but the
lock contact has not closed in the
time set.

-

Check shaft doors
mechanically (smooth
running).

-

Check door lock contacts.

-

Increase door lock timeout
(see “Lock Delay” on
page 144).

36

CAR LIGHT FAILURE

Power sensor indicates car light is
not working.

-

Check car light.

-

Check power sensor on FSM
(see “FSM: X14” on page 64).

37

REGULATOR ERROR

Error message from the frequency
converter when using a converter
with serial control.

Check error list of the frequency
converter. The number of the
regulator error corresponds to
the error code in the
documentation of the frequency
converter.

38

REFILL PUMP TIMEOUT

Error during refilling of the hydraulic
counterweight.

The cut-off pressure for refilling
has not been reached within 30
seconds. Check function and
control of the refill valve.

39

SAFETY CURTAIN BRK.

The safety curtain has been
interrupted while the car was
moving.

Check function and control of the
safety curtain (see “SS-Curtain”
on page 145).

40

SAFETY CURTAIN FAIL

Error during test of safety curtain.

The FST-Controller issues a test
signal for the safety curtain via
FSM X10.2 before each drive.
The safety curtain acknowledges
the test signal with an
interruption of the safety circuit
(VSM X1.3).

-

Check operation of the safety
curtain.

-

Check duration of the test
impulse in

MAIN MENU –

Doors – Doors Basic

– SS-CurtainWait

(see

“SS-CurtainWait” on
page 145).

41

X12-SERIAL OFF

No serial connection to the
frequency converter (FST X12,
DCP).

-

Check connection cable
between FST X12 and
frequency converter.

-

Check settings of the
frequency converter (DCP03).

42

X-12 SERIAL BAD

Serial connection to the frequency
converter is faulty (FST X12, DCP).

-

Check connection cable
between FST X12 and
frequency converter.

-

Check shield of the connection
cable.

43

UPS FAILURE

UPS FAILURE–ON

State change at the programmable
input “UPS FAILURE” for monitoring
UPS error messages.

Check operation of the UPS.

Code

Message

Description

Reason

«
...
157
158
159
160
161
...
»

Содержание FST















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для FST

Бренд: GARDTEC Страницы: 48

Бренд: FAAC Страницы: 64

Бренд: TCS Basys Controls Страницы: 2

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

Бренд: eclisse Страницы: 40

Бренд: Eaton Страницы: 100

Бренд: Gate Motors Страницы: 6

Бренд: Parker Страницы: 32

Бренд: Rayrun Страницы: 4

AeGIS 7000 Series

Бренд: PACH & COMPANY Страницы: 2

Бренд: Watts Страницы: 4

Бренд: ZKTeco Страницы: 20

Бренд: ZKTeco Страницы: 8

Бренд: ZKTeco Страницы: 10

Бренд: ZKTeco Страницы: 121

Бренд: ZKTeco Страницы: 12

Бренд: ZKTeco Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды