New lift FST Скачать руководство пользователя страница 141

Страница: 141 / 174

1 Menu tree

1.6 MAIN MENUE – Calls

FST_HB.EN04/03

139

1.6 MAIN MENUE – Calls

Special Call Mode

Pending calls can be processed in three different ways:

Menu item

Description

Setting range

Call Floor –

Config

Landing call program for each floor:

No Button: No landing button available.

DOWNcollect: One button for downward calls available.

UP–collect: One button for upward calls available.

Two button: Buttons for upward and downward calls
available.

STOPcollect: Upward and downward calls use the same
button.

No Button …
STOPcollect

Call Floor –

Door function

Door program for each floor:

Single: Only one shaft door available.

Selective: Shaft doors are handled selectively.

Order: Locked shaft doors are handled in the specified
order.

Sequence: Locked shaft doors are handled following the
order the calls were issued.

Through: All shaft doors are handled simultaneously.

Single …
Through

Call Floor –

Door

Door program for each car door:

X: Door deactivated

>A<: Door A active, default position closed.

<A>: Door A active, default position open.

The same settings apply to car doors B and C.
If an

is entered the landing and in-car calls for that side of

the door on that floor are locked.

>A< ... X

Special Call Mode

Call programs for landing and in-car calls (see “Special Call
Mode” on page 139).

Standard
Non-Collective
Single-Call Mode

Lift-Boy Mode

Activate Lift-Boy Mode (see “Lift-Boy Mode” on page 140).

YES
NO

Setting

Method

Standard

Landing and in-car calls are collected.

Non-Collective

Only one call at a time is accepted.

The car is reserved as long as it is moving or
a door is open.

Landing calls are locked when the car is
reserved.

Single-Call Mode

Only one call at a time is accepted.

The car is reserved as long as it is moving or
a door is open.

If the car is reserved landing calls are
collected but not processed.

When the car is released the oldest call will
be processed first.

Содержание FST















































































































































































Результаты поиска

Содержание FST

Отзывы:

Похожие инструкции для FST

Бренды по названию

Популярные бренды

New lift FST, Руководство пользователя

Результаты поиска

Содержание FST

Отзывы:

Похожие инструкции для FST

Бренды по названию

Популярные бренды