New Holland FR450 TIER 3 Скачать руководство пользователя

Страница: 66 / 81

Engine - Engine and crankcase

36. On the right-hand side, connect the connector

(17)

and other connectors to the feed rolls hydrostatic
pump (in case of single drive).

NOTE:

If installed, do the same for the attachment hydro-

static pump (in case of double drive).

ZEIL13FR00324AZ

37. On the left-hand side, connect the tube

(108)

to the

engine.

ZEIL13FR00320AB

38. On the left-hand side, connect the Engine Control Unit

(ECU) fuel tube

(56)

. Connect the ECU connector

(51)

to the ECU

(52)

ZEIL13FR00319AB

39. On the right-hand side, connect the air-conditioning

hose

(48)

and

(49)

from the air-conditioning pump

(50)

ZEIL13FR00318AB

47812470 23/02/2015

10.1 [10.001] / 29

Содержание FR450 TIER 3


















































































Результаты поиска

Содержание FR450 TIER 3

Отзывы:

Похожие инструкции для FR450 TIER 3

Бренды по названию

Популярные бренды

New Holland FR450 TIER 3, Руководство по обслуживанию

Результаты поиска

Содержание FR450 TIER 3

Отзывы:

Похожие инструкции для FR450 TIER 3

Бренды по названию

Популярные бренды