New Holland FR450 TIER 3 страница 29 Скачать руководство пользователя | Manualshive

Страница: 29 / 81

background image

INTRODUCTION

Basic instructions - Chain Wear Tables - Roller Chains

Chain Wear

The individual joints in a roller chain articulate as they enter and leave the sprockets. This articulation results in wear
on the pins and bushings. A material is worn away from these surfaces the chain will gradually elongate.

ZEIL10GH0003A0B

1

Chains do not "stretch" - material is removed from pin and bushing.

(1)

: 2x pitch

(2)

: 2x pitch + wear

(3)

: elongation due to pin and bushing wear.

Elongation is normal and may be minimized by proper lubrication and drive maintenance. The rate of wear is depen-
dent upon: the relationship between the load and the amount of bearing area between pin and bushing, the material
and surface condition of the bearing surfaces, the adequacy of lubrication and the frequency and degree of articulation
between pins and bushings.
The latter is determined by the quantity of sprockets in the drive, their speeds, the number of teeth and the length of
the chain in pitches.

ZEIL10GH0015A0A

2

Measurement of Chain For Wear Elongation

Relatively accurate wear measurements can be made by using the above illustration. Measure as closely as possi-
ble from the center of one pin to the center of another. The more pitches (pins) contained within the measurement
increase the accuracy. If the measured value exceeds the nominal by more than the allowable percentage the chain
should be replaced.
The maximum allowable wear elongation is approximately

3 %

for most industrial applications, based upon sprocket

design. The allowable chain wear in percent can be calculated using the relationship: 200/

(N)

, where

(N)

is the

number of teeth in the large sprocket.
This relationship is often useful since the normal maximum allowable chain wear elongation of

3 %

is valid only up to

67 teeth in the large sprocket. In drives having fixed center distances, chains running in parallel or where smoother
operation is required, wear should be limited to approximately

1.5 %

.

47812470 23/02/2015

22

«
...
27
28
29
30
31
...
»

Содержание FR450 TIER 3


















































































Отзывы:

Нет отзывов

Похожие инструкции для FR450 TIER 3

Бренд: Taurus Страницы: 28

Бренд: Kärcher Страницы: 54

Бренд: ABB Страницы: 85

Бренд: Napoleon Страницы: 2

Бренд: Raytheon Страницы: 62

Бренд: KBT Страницы: 12

ABS-Lock DH04 Series

Бренд: ABS Страницы: 4

Coronis 5MP Mammo

Бренд: Barco Страницы: 4

Бренд: Barco Страницы: 167

Color Coronis 2MP

Бренд: Barco Страницы: 156

Color Coronis 2MP

Бренд: Barco Страницы: 12

Бренд: Barco Страницы: 39

Бренд: Barco Страницы: 158

Бренд: CAMAG Страницы: 40

Бренд: TC Electronic Страницы: 4

Бренд: TC Electronic Страницы: 6

Бренд: TC-Helicon Страницы: 12

Бренд: TC Electronic Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды