New Holland E75CSR Скачать руководство пользователя | Manualshive

Страница: 15 / 51

background image

INTRODUCTION

3. If an abnormality is detected, repair or replace the parts.

Reassembling hydraulic equipment

1. During the parts cleaning, ventilate the room.

2. Before assembly, clean parts roughly first, and then completely.

3. Remove adhering oil by compressed air, and apply hydraulic oil or gear oil, and then assemble them.

4. Replace the removed O-ring, back-up rings and oil seal with new ones, and apply grease oil on them before

assembling.

5. Removes dirt and water on the surface on which liquid sealant are applied, decrease them, and apply liquid sealant

on them.

6. Before assembling, remove rust preventives on new parts.

7. Use special tools to fit bearings, bushing and oil seal.

8. Assemble parts matching to the marks.

9. After completion, check that there is no omission of parts.

Installing hydraulic equipment

1. Confirm hydraulic oil and lubrication oil.

2. Air release is required in the following cases:

A. Change of hydraulic oil

B. Replacement of parts on suction pipe side

C. Removing and attaching hydraulic pump

D. Removing and attaching swing motor

E. Removing and attaching travel motor

F. Removing and attaching hydraulic cylinder

3. For air bleed of hydraulic pump and swing motor,

loosen drain plug on the upper part, start engine, and
run in low idling, then bleed air until hydraulic oil is
comes out. After completion of comes, tighten plug
securely.

4. For air bleed of travel motor and hydraulic cylinder,

starts engine and operate it for

10 min

or more at no

load and low speed.

5. Air in pilot circuit can be bleed out by only operating

digging, swing and traveling motions thoroughly.

6. Check hydraulic oil level.

Move attachments to hydraulic oil check position, and
check hydraulic oil level of tank. Refill oil if the oil level
is lower than the specified level.
How to check oil level of hydraulic oil tank.

TULTSM2300067A

1

ATTENTION:

If hydraulic oil and lubricating oil are not filled and also air bleed is not performed, the hydraulic equip-

ment may be damaged.

ATTENTION:

For cylinder, don’t move it to the stroke end at beginning.

47488366A 13/03/2013

10

«
...
13
14
15
16
17
...
»

Содержание E75CSR




















































Отзывы:

Нет отзывов

Похожие инструкции для E75CSR

Бренд: Komatsu Страницы: 31

Бренд: Savaria Страницы: 16

Бренд: Savaria Страницы: 16

Бренд: Savaria Страницы: 24

Бренд: OLEO Страницы: 16

Бренд: Forankra Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды