New Buck Corporation 1127B Скачать руководство пользователя страница 35

Страница: 35 / 43

OBSERVED

PROBLEM

3. ODS/PILOT lights but flame

goes out when control knob
is released

4. Burner does not light after

ODS/Pilot is lit

POSSIBLE

PROBLEM

1. Control knob is not fully

pressed in

2. Control knob not pressed in

long enough

3. Safety interlock system has

been triggered (if equipped)

4. Manual shutoff valve not

fully open

5. Thermocouple connection

loose at control valve.

6. Pilot flame not touching

thermocouple, which allows
thermocouple to cool,
causing pilot flame to go
out. This problem can be
caused by one or both of the
following:

A) low gas pressure

B) dirty or partially

clogged ODS/Pilot

7. Control valve damaged

1. Burner orifice is clogged

2. Inlet gas pressure is too low

SOLUTION

1. Press control knob completely

2. After ODS/Pilot lights keep

control knob pressed 30
seconds

3. Wait 1 minute for safety

interlock system to reset.

4. Fully open manual shutoff

valve

5. Hand tighten until snug, then

tighten 1/4 turn

6. A) Contact local propane gas

company

B) Clean ODS/Pilot (See
“Cleaning and Maintenance”),
or replace ODS/Pilot
assembly

7. Replace valve control

1. Clean burner (see “Cleaning

and Maintenance”) or replace
burner orifice

2. Contact local propane gas

company

Содержание 1127B












































Результаты поиска

Содержание 1127B

Отзывы:

Похожие инструкции для 1127B

Бренды по названию

Популярные бренды

New Buck Corporation 1127B, Руководство пользователя

Результаты поиска

Содержание 1127B

Отзывы:

Похожие инструкции для 1127B

Бренды по названию

Популярные бренды