New Buck Corporation 1127B Скачать руководство пользователя страница 34

Страница: 34 / 43

OBSERVED

PROBLEM

1. Igniter button is pressed. No

spark at ODS/Pilot

2. Igniter button is pressed

Spark at ODS/Pilot
No Ignition

POSSIBLE

CAUSE

1. Igniter electrode positioned

incorrectly

2. Igniter electrode broken
3. Igniter electrode not

connected to igniter cable

4. Igniter cable pinched or wet

5. Piezo igniter nut is loose

6. Broken igniter cable
7. Bad piezo igniter

1. Gas supply turned off or

manual shutoff valve is
closed

2. Control knob not in “PILOT”

position

3. Control knob not pressed in

while in “PILOT” position

4. Air in gas lines when installed

5. Depleted gas supply

6. ODS/Pilot is clogged

7. Gas regulator setting is not

correct

SOLUTION

1. Replace igniter

2. Replace igniter
3. Reconnect igniter cable

4. Free igniter cable if pinched

by any metal or tubing. Keep
igniter cable dry.

5. Tighten nut holding piezo

igniter to heater cabinet. Nut
is located inside heater
cabinet at top.

6. Replace igniter cable
7. Replace piezo igniter

1. Turn on gas supply or open

manual shutoff valve

2. Turn control knob to “PILOT”

position

3. Press in control knob while in

“PILOT” position.

4. Continue to hold down control

knob. Repeat igniting
operation until air is removed.

5. Contact local propane gas

company

6. Clean ODS/Pilot or replace

ODS/Pilot assembly

7. Replace gas regulator

Содержание 1127B












































Результаты поиска

Содержание 1127B

Отзывы:

Похожие инструкции для 1127B

Бренды по названию

Популярные бренды

New Buck Corporation 1127B, Руководство пользователя

Результаты поиска

Содержание 1127B

Отзывы:

Похожие инструкции для 1127B

Бренды по названию

Популярные бренды