Neumo 66TX51341313131 Скачать руководство пользователя страница 31

Страница: 31 / 92

Container Cleaning System TANKO®EX-R64T

3 Design and Function

Translation - Operating/installation instructions 2020/03

23/80

Design and Function

3.1

Design

Figure 3.1-1: TANKO-EX-R64T device carrier without cleaning devices

The TANKO-EX-R64T device carrier consists of the following main components:

1 Media connection [MA]

2 Actuator

3 Distribution for connections, freely rotating

4 Connection for cleaning devices

The devices are made of stainless steel. They do not have any electrical equipment.

Cleaning device carriers with different arm lengths are available for different purposes and container sizes.

Only TANKO-EX-S30 or TANKO-EX-RB-30 may be used as cleaning devices.

Содержание 66TX51341313131





























































































Результаты поиска

Содержание 66TX51341313131

Отзывы:

Похожие инструкции для 66TX51341313131

Бренды по названию

Популярные бренды

Neumo 66TX51341313131, Руководство по эксплуатации и установке

Результаты поиска

Содержание 66TX51341313131

Отзывы:

Похожие инструкции для 66TX51341313131

Бренды по названию

Популярные бренды