Network Technologies SERIMUX-CS Series Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 65

background image

NTI SERIMUX SERIES CONSOLE SWITCH

7

Dual Power Option

The SERIMUX-CS-xDP has two IEC connectors on the rear, for connection to two separate power sources. If the power source
connected to “PWR 1” fails, the ENVIROMUX will automatically and without interruption switch over to the power source
connected to “PWR 2” .

Note: If only one power source is used, it should be connected to “PWR 1”.

Note: The power ON/OFF switch is located on the front panel of SERIMUX when two IEC connectors are present.

Figure 5- Power connections for SERIMUX with Dual Power option

CONSOLE

9

10

11

12

13

14

15

16

1

2

3

4

5

6

7

8

25

26

27

28

29

30

31

32

21

22

23

24

17

18

19

20

RESET

ISP

ETHERNET

NETWORK TECHNOLOGIES INC

Tel:330-562-7070

1275 Danner Dr, Aurora, OH 44202

www.networktechinc.com

Rear View of SERIMUX

PWR 2

PWR 1

250V,2A

250V,2A

UPS
1

UPS
2

PWR 1

PWR 2

Uninterruptible Power Supplies

«
...
10
11
12
13
14
...
»

Содержание SERIMUX-CS Series


































































Отзывы:

Нет отзывов

Похожие инструкции для SERIMUX-CS Series

Бренд: N-Tron Страницы: 20

COOPER POWER SERIES

Бренд: Eaton Страницы: 16

OfficeConnect 5

Бренд: 3Com Страницы: 2

OfficeConnect 3C1670500C

Бренд: 3Com Страницы: 18

ServSwitch KV1510A

Бренд: Black Box Страницы: 16

Бренд: Televes Страницы: 24

AVlink VAX-8404F

Бренд: C&C TECHNIC Страницы: 2

Бренд: Lindy Страницы: 12

S-Mix-Pro 18*18

Бренд: Kensence Страницы: 24

Бренд: Metra Electronics Страницы: 8

Бренд: NeoPro Страницы: 36

Бренд: Edimax Страницы: 8

TK-423K - USB/PS/2 KVM Switch

Бренд: TRENDnet Страницы: 14

Бренд: Lancom Страницы: 71

Бренд: BJ Live Страницы: 2

Бренд: Angustos Страницы: 15

Бренд: EnGenius Страницы: 72

Master View CS-172

Бренд: ATEN Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды