manualshive.com logo in svg

Network Equipment Technologies SBC 2000, Руководство пользователя

Поделиться
Скачать
Network Equipment Technologies SBC 2000 Скачать руководство пользователя страница 28

The T1/E1 ports are connected to the public network using 4-wire shielded 26 AWG or larger twisted pair telecommunication line cords with RJ-48
connectors.

T1/E1 RJ-48 Connector

T1/E1 Connector Pinouts

Pin Number

Description

1

Receive Ring

2

Receive Tip

3

no connection

4

Transmit Ring

5

Transmit Tip

6

no connection

7

no connection

8

no connection

Installing the UX2000 Hardware

This section describes how to prepare for and physically install a UX system.

Installation Warnings
Preparing for Installation
Installing the UX Chassis in a 4-Post Equipment Rack
Installing the UX Chassis in a 2-Post Equipment Rack
Installing Interface Cards
Installing Ground Wire, Power Cables and Connect Power
Installing the Cable Management Bracket
Next Steps

Installation Warnings

Review the 

, 

 and 

 before installing the UX chassis.

Safety Requirements Precautions

UX2000 Chassis Installation Requirements

Do not remove the top panel of the UX chassis. Operating the UX system with the top panel removed will cause hardware components
to overheat and fail. Unauthorized removal of the top panel will void your product warranty and service agreement.

Содержание SBC 2000







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды