manualshive.com logo in svg

Network Equipment Technologies SBC 2000, Руководство пользователя

Поделиться
Скачать
Network Equipment Technologies SBC 2000 Скачать руководство пользователя страница 32

2.  

1.  
2.  

3.  

Installing Interface Cards

UX interface cards are delivered separately from the UX chassis. Install the cards in the UX chassis before powering on the unit. For more information
about UX interface cards, see Interface Cards. For more information about installing and removing interface cards, see 

Inserting and Removing Interface

.

Cards

You must power down the UX system before installing or removing Interface Cards. Hot swapping of Interface Cards is not supported in
UX 1.2.

To Insert an Interface Card

Carefully insert the card so that the left and right edges slide into the mounting slots.
Grip the outside of the attachment levers and push toward the inside of the card until the card locks into place.

The red buttons click and pop out when the card is properly locked into place.

Tighten the screws on the right and left side of the interface card.

Содержание SBC 2000







































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды