NETGEAR PS121v2 - USB Mini Print Server Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 50

NETGEAR PS121v2 - USB Mini Print Server Скачать руководство пользователя страница 22

NETGEAR USB Multifunction Printer Server PS121v2 User Manual

2-6

Setup

v1.1, September 2006

5.

Click

Next

to proceed to the “Activate Network” stage, where the IP address settings and

device name will be displayed.

The settings recommended by the installation assistant will usually work well.

6.

Click

Next

to continue. If the installation assistant prompts you for a password, type

password

in the password field and click

OK

to continue to the “Verify Settings” stage.

7.

If the installation instructions prompt you for a password, type

password

and continue.

8.

When you reach the “Finalize Setup” stage, click

Print Test Page

to confirm that the

installation of the

print server

was successful.

9.

Click

Next

and

Finish

to close the installation assistant.

Figure 2-4

Note:

Take a note of the the IP address assigned to the print server. You will need

reserve this address in your router to be permanently assigned to the print
server, and use it to access the Web-based Graphical User Interface.

«
...
20
21
22
23
24
...
»

Содержание PS121v2 - USB Mini Print Server



















































Отзывы:

Нет отзывов