NETGEAR ProSafe 7000 Скачать руководство пользователя | Manualshive

Страница: 63 / 562

background image

5-1

v1.0, June 2010

Chapter

5

Routing Information Protocol

In this chapter, the following examples are provided:

•

“Enable Routing for the Switch” on page

5-2

•

“Enable Routing for Ports” on page

5-3

•

“Enable RIP for the Switch” on page

5-5

•

“Enable RIP for Ports 1/0/2 and 1/0/3” on page

5-6

•

“VLAN Routing RIP Configuration” on page

5-8

Routing Information Protocol (RIP) is one of the protocols which may be used by routers to exchange
network topology information. It is characterized as an “interior” gateway protocol, and is typically used in
small to medium-sized networks.

A router running RIP will send the contents of its routing table to each of its adjacent routers every 30
seconds. When a route is removed from the routing table it will be flagged as unusable by the receiving
routers after 180 seconds, and removed from their tables after an additional 120 seconds.

There are two versions of RIP:

•

RIPv1 defined in RFC 1058

–

Routes are specified by IP destination network and hop count

–

The routing table is broadcast to all stations on the attached network

•

RIPv2 defined in RFC 1723

–

Route specification is extended to include subnet mask and gateway

–

The routing table is sent to a multicast address, reducing network traffic

–

An authentication method is used for security

The 7000 Series Managed Switch supports both versions of RIP. You may configure a given port:

•

To receive packets in either or both formats

•

To transmit packets formatted for RIPv1 or RIPv2 or to send RIPv2 packets to the RIPv1 broadcast
address

•

To prevent any RIP packets from being received

•

To prevent any RIP packets from being transmitted

«
...
61
62
63
64
65
...
»

Содержание ProSafe 7000



















































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProSafe 7000

Бренд: H3C Страницы: 204

H3C S7500E Series

Бренд: H3C Страницы: 44

H3C S7500E Series

Бренд: H3C Страницы: 11

H3C S7500E Series

Бренд: H3C Страницы: 25

Бренд: H3C Страницы: 46

Бренд: LEGRAND Страницы: 2

MyPower S2300-28TC-AC

Бренд: Maipu Страницы: 31

Бренд: P-Link Computer Страницы: 92

QuantaMesh T1048-LB9M

Бренд: QCT Страницы: 34

Бренд: SMART-AVI Страницы: 2

SIL IntelliPoint RF S*R*L Series

Бренд: Ametek Страницы: 93

Бренд: StarTech.com Страницы: 16

Бренд: Hama Страницы: 14

Бренд: Minicom Страницы: 16

Бренд: Pilz Страницы: 20

AVS-OCT-3264-360

Бренд: AMX Страницы: 1

Бренд: Black Box Страницы: 57

Бренд: HighSecLabs Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды