Net to Net Technologies 4-Module IP DSLAM IPD4000E Скачать руководство пользователя

Страница: 15 / 17

3.0 ADDITIONAL INFORMATION

3.1 Fan Module

The IPD4000E fan module is installed vertically to the right of the interface module

slots. It comes pre-installed and should not be removed unless it is being replaced. Fan

functionality is indicated by a FAN LED on your management module (all models): NO

illumination or solid GREEN illumination indicates all fans are currently functioning,

solid AMBER illumination indicates one or more of the four fans are no longer

functioning.

3.2 IPD4000E Interface Capacity

4 interface module slots

1 management module slot

8 RJ21 50-pin female Telco connectors

3.3 Technical Support

3.3.1 Net to Net Technologies' Web Site

The following information can be found at

http://www.nettonet.com/support

DSL Distance and Bandwidth Quick Reference Chart

Firmware Downloads (for applicable modules)

IPD4000E FRONT VIEW

Fan Module

MANAGEMENT MODULE

Fan LED

AUTION

Do not operate the IPD4000E without a fan module or with a fan module that is not functioning properly.

Page 15 of 17

IPD4000E Installation Instructions 220-0000097 rev01

Содержание 4-Module IP DSLAM IPD4000E


















Результаты поиска

Содержание 4-Module IP DSLAM IPD4000E

Отзывы:

Похожие инструкции для 4-Module IP DSLAM IPD4000E

Бренды по названию

Популярные бренды

Net to Net Technologies 4-Module IP DSLAM IPD4000E, Руководство по установке

Результаты поиска

Содержание 4-Module IP DSLAM IPD4000E

Отзывы:

Похожие инструкции для 4-Module IP DSLAM IPD4000E

Бренды по названию

Популярные бренды