Net to Net Technologies 4-Module IP DSLAM IPD4000E Скачать руководство пользователя

Страница: 17 / 17

limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instruction manual, may

cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in

which case the user will be required to correct the interference at his own

expense.

Caution: Changes or modifications not expressly approved by the

manufacturer could void the user’s authority to operate the equipment.

3.4.2.2 Industry Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du

Canada.

3.4.2.3 Europe

This Class A product complies with European Norm EN55022.

Warning: In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate

measures to correct the situation.

™ The Net to Net Logo is a trademark of Net to Net Technologies, Inc.

Worldwide Headquarters

Net to Net Technologies

112 Corporate Drive

Portsmouth, NH 03801

USA

+1 877-638-2638

[email protected]

http://www.NetToNet.com/

EMEA Headquarters

Net to Net Technologies

Victoria House 19 Park Way

Newbury Berkshire RG14 1EE

+44 (0) 1635 570950

[email protected]

Page 17 of 17

IPD4000E Installation Instructions 220-0000097 rev01

Содержание 4-Module IP DSLAM IPD4000E


















Результаты поиска

Содержание 4-Module IP DSLAM IPD4000E

Отзывы:

Похожие инструкции для 4-Module IP DSLAM IPD4000E

Бренды по названию

Популярные бренды

Net to Net Technologies 4-Module IP DSLAM IPD4000E, Руководство по установке

Результаты поиска

Содержание 4-Module IP DSLAM IPD4000E

Отзывы:

Похожие инструкции для 4-Module IP DSLAM IPD4000E

Бренды по названию

Популярные бренды