background image

Net Safety Monitoring 

MAN-0015 Rev 14 UVIRS-A/AR 

November 07, 2008 
 

 

 

 

I

MPORTANT 

I

NFORMATION

 

This manual is for informational purposes only. Although every effort has 
been made to ensure the correctness of the information, technical 
inaccuracies may occur and periodic changes may be made without notice. 
Net Safety Monitoring Inc., assumes no responsibility for any errors 
contained within this manual. 

If the products or procedures are used for purposes other than as described in 
the manual, without receiving prior confirmation of validity or suitability, 
Net Safety Monitoring Inc., does not guarantee the results and assumes no 
obligation or liability. 

No part of this manual may be copied, disseminated or distributed without 
the express written consent of Net Safety Monitoring Inc. 

Net Safety Monitoring Inc., products are carefully designed and 
manufactured from high quality components and can be expected to provide 
many years of trouble free service. Each product is thoroughly tested, 
inspected and calibrated prior to shipment. Failures can occur which are 
beyond the control of the manufacturer. Failures can be minimized by 
adhering to the operating and maintenance instructions herein. Where the 
absolute greatest of reliability is required, redundancy should be designed 
into the system. 

Warranty 

Net Safety Monitoring Inc., warrants its sensors against defective parts and 
workmanship for a period of 24 months from date of purchase; other 
electronic assemblies for 36 months from date of purchase. 

No other warranties or liability, expressed or implied, will be honoured by 
Net Safety Monitoring Inc. 

Contact Net Safety Monitoring Inc or an authorized representative for details. 

We welcome your input at Net Safety Monitoring. If you have any comments 
please contact us at the phone/address below or visit our web site and 
complete our on-line customer survey: 

www.net-safety.com

 

Contact Information 

Net Safety Monitoring Inc. 
2721 Hopewell Place NE 
Calgary, AB 
Canada 
T1Y 7J7 
Telephone: (403) 219-0688 Fax: (403) 219-0694 
www.net-safety.com 
E-mail: [email protected] 

Copyright © 2007 Net Safety Monitoring Inc.  

Printed in Canada 

Содержание UV/IRS-A






























Отзывы: