background image

6

radio Key (rK4) 

oPeRAtion

rK4 radio Keys have four buttons for operating your 
securityGuarD iii.

Press the 

 button to Disarm the system or to si-

lence alarms.

Press the

button to arm the system or press 

twice for home mode (if enabled on your system.)

Press the 

 button to sound the Panic alarm.

Press the 

 button for auxiliary functions as pro-

grammed by your installer.

bAtteRy RePLAcement

your rK4 radio Keys are sealed units with an ex-
pected battery life of 10 years. low battery warning 
might indicate a battery fault or the battery has been 
depleted by continuous presses. contact ness or 
your sGiii dealer for advice.

* example device 

number

radio Keypad (rKP) 

oPeRAtion

rKP radio Keypads have a full Pin pad for operat-
ing your securityGuarD iii using 3 to 6 digit user 
codes. your installer will set up and program the 
rKP to suit.

buttons

  used with your user code to arm the system.
  used with your user code to arm home mode.

  enter button, used when arming and disarming.

 

  

(Press together) 

sounds the Panic alarm

 

 not used.

  used by your installer only.

Lights

 Valid: Flashes once when a valid radio signal is 

sent to the securityguard.

 low Battery: if flashing indicates that the rKP's 

internal battery is low. replace the battery.

bAtteRy RePLAcement

carefully open the rKP radio Keypad by pushing 
both tabs at the top of the unit using a flat-bladed 
screwdriver or blunt knife. 
insert a new high energy lithium 9V battery and 
then test the sensor.

* example device 

number

insert the new high 
energy lithium 9V 
battery.

Содержание SecurityGuard III













Отзывы: