Nescafe Dolce Gusto KRUPS KP 2100 Скачать руководство пользователя страница 19

Страница: 19 / 60

R E P A I R

R E P A I R

This chapter contains special security and assembling notes.

Tools and repair accessories

With the following tools, all described repair work can be done:
•

Torx screwdriver for security screws Pin-TX 10

•

Phillips screwdriver no. 1 and 2

•

Screwdriver with 4 mm width

•

Pointed flat pliers

•

Flat nose pliers

•

Fork wrench no. 8

•

Fork wrench no. 12

•

Cutter (stanley knife)

•

Heat conducting paste

Repair work without disassembling the machine

Without disassembling the machine, you can replace or repair the following parts:
•

water tank assembly and cap

•

capsule holder

•

injector plate

•

drip tray and drip grid

•

capsule bin

Non-observance
can lead to injuries

and damages!

A pin-torx screw
head looks like this:

Содержание KRUPS KP 2100





























































Результаты поиска

Содержание KRUPS KP 2100

Отзывы:

Бренды по названию

Популярные бренды

Nescafe Dolce Gusto KRUPS KP 2100, Руководство по обслуживанию

Результаты поиска

Содержание KRUPS KP 2100

Отзывы:

Бренды по названию

Популярные бренды