NEFF C67M70.0GB, Руководство пользователя

Страница: 15 / 40

15
Changing the basic settings
Requirement: the operating mode selector must not be pushed
in.
1.
Press and hold the ± button for a few seconds.
The first basic setting is displayed on the text display.
2.
Press the
±
button repeatedly until the required basic setting
is shown.
3.
Use the temperature selector to make the desired setting.
4.
Press and hold the Info button ± for a few seconds.
Your setting is applied.
You can change the settings at any time.
Care and cleaning
With careful care and cleaning your microwave oven will retain
its looks and remain good order. We will explain here how you
should care for and clean your appliance correctly.
In this section, you will find information on
■
Cleaning and care of your appliance
■
Cleaning agents
■
Cleaning the glass panels
■
Cleaning the glass cover
ã=
Risk of short circuit!
Never use high-pressure cleaners or steam cleaners to clean
the oven.
ã=
Risk of burns!
Never clean the appliance immediately after switching off. Let
the appliance cool down.
Notes
■
Slight differences in colour on the front of the appliance are
caused by the use of different materials, such as glass,
plastic and metal.
■
Shadows on the door panel which look like streaks, are
caused by reflections made by the oven light.
■
Enamel is baked on at very high temperatures. This can
cause some slight colour variations. This is normal and does
not affect their function. The edges of thin trays cannot be
completely enamelled. As a result, these edges can be
rough. This will not impair the anti-corrosion protection.
■
Unpleasant odours, e.g. after fish has been prepared, can be
removed very easily. Add a few drops of lemon juice to a cup
of water. Place a spoon into the container as well, to prevent
delayed boiling. Heat the water for 1 to 2 minutes at
maximum microwave power.
Cleaning agents
To ensure that the different surfaces are not damaged by using
the wrong cleaning agent, observe the information in the table.
Do not use
■
sharp or abrasive cleaning agents,
■
metal or glass scrapers to clean the glass in the appliance
door,
■
metal or glass scrapers to clean the door seal,
■
hard scouring pads and sponges,
■
cleaning agents with high concentrations of alcohol.
Wash new sponge cloths thoroughly before use.
™… ‹
= Continue when door shut:
off
‚
= automatic
‹ = off*
Way in which operation is continued when
the oven door is opened and closed
again
*Continue operation with
ƒ
™†
Adjust individually
-3
ÙÙÙØÙÙÙ +3
e.g. increasingly well done cooking
result
-3 ÙÙÙÙÙØÙ +3
Change the cooking result for all
automatic programmes
to the right = more intensive
to the left = less intensive
™‡
Set the mains voltage
‚
= 220-230V
ƒ
= 230-240 V
Adjust the mains voltage
™ˆ ‚
= do not restore factory settings
ƒ
= restore factory settings
Reverse all changes and restore basic
settings.
Basic setting Options Explanation
Area Cleaning agents
Appliance front Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth. Do not use glass cleaners or
metal or glass scrapers for cleaning.
Stainless steel Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth. Remove flecks of limescale,
grease, starch and albumin (e.g. egg
white) immediately. Corrosion can form
under such residues. Special stainless
steel cleaning agents can be obtained
from the after-sales service or from
specialist shops.
Oven Hot soapy water or a vinegar solution:
Clean with a dish cloth and dry with a
soft cloth.
If oven is very dirty: use oven cleaner,
but only when oven is cold. It is best to
use a stainless-steel sponge.
Glass cover for the
oven light
Hot soapy water:
Clean with a dish cloth.
Control panel/outer
door panel
Glass cleaner:
Wipe dry immediately using a soft cloth.
Do not use a glass scraper.
Inner door glass Glass cleaner:
Wipe dry with a soft cloth. Do not use a
glass scraper.
Seal Hot soapy water:
Clean with a dish cloth, do not scour.
Do not use a metal or glass scraper for
cleaning.
Accessories Hot soapy water:
Soak and clean with a dish cloth or a
brush.