background image

Page 17 of 28

To access by USB, simply connect the unit to your PC. If you have installed Neets Project Design

-

er, all necessary drivers are already installed on your PC. (Note: If not available, please visit www.

neets.dk and navigate to the download page for the amplifier. Here you find the driver files along 

with detailed information on how to install the driver.)

 

To access the unit’s webserver home page,  open your browser and type in: http://neetsweb/ or 

http://192.168.0.4/ and the amplifier homepage should pop up.

 

To access by LAN, connect the amplifier to your LAN and type in the IP address of the unit and 

the homepage should pop up. LAN access requires that you know the IP address of your amplifier 

or preamplifier and that this address is within the IP range of your network. If this is not the case 

please change the settings using USB config connection first.

Control from LAN by remote protocol

Connect the amplifier or preamplifier to the local area network to allow control via LAN.

• 

Network Protocol: TCP

• 

Control port: 5000 (only one active connection at a time)

The commands for LAN control can be found on page 20.

Control from RS-232 by remote protocol

Connect a RS-232  device to RS-232 port 1 with the following default settings.

• 

Baudrate: 19.200

• 

Databit: 8

• 

Stopbit: 1

• 

Parity: None

The amplifier can be controlled from RS-232 port 1 only. Please be aware that RS-232 control is 

deactivated if the amplifier is also controlled  by a LAN connection.

 

The commands for RS-232 control can be found on page 20.

© CreativeGeist 2016

Alle rettigheder forbeholdes

[email protected] | www.creativegeist.dk

T H I N K

,

T H I N K   A G A I N

,

D E S I G N

Содержание 2:25





























Отзывы: