background image

Page 26 of 28

LAN settings

The LAN settings commands are used to configure the LAN interface on the amplifier or preampli

-

fier. Please remember to store the settings with the Save command if you want the unit to re

-

member settings after a reboot. 

 

All commands start with: NEUNIT=<A>,SETTINGS=LAN,

 

Where <A> is the unit ID, default 1. All commands must end with a \CR.

Description:

Syntax

<X>

Default <X>

R/W

Set unit IP address

IPAD-

DRESS=<X>

xxx.xxx.xxx.xxx 192.168.254.252

R/W

Set unit sub net

SUBNET=<X>

xxx.xxx.xxx.xxx 255.255.255.0

R/W

Set gateway

GATEWAY=<X> xxx.xxx.xxx.xxx 192.168.254.252

R/W

Select if DHCP is used or not.

DHCP=<X>

ON, OFF

OFF

R/W

LAN speed (F = Full duplex, H = 

Half duplex)

SPEED=<X>

10F, 10H, 

100F, 100H, 

AUTO

100F

R/W

Set control TCP Port

IPPORT=<X>

0-65555

5000

R/W

Get the MAC address of the unit. MACAD

-

DRESS=<X>

xx:xx:xx:xx:xx

R

Set the multicast address the 

unit must use when communi

-

cating with other Neets units by 

LAN. (Remember when changing 

this value, it must also be done 

on all other systems this unit 

must communicate with.)

After changing the multicast 

address you must send the Save 

command to make sure that the 

system uses this address at next 

reboot.

MULTICASTAD

-

DRESS=<X>

xxx.xxx.xxx.xxx 224.10.10.25

R/W

Set the multicast port the unit 

must use when communicating 

with other Neets units by LAN. 

(Remember when changing this, 

it must also be done in all other 

systems this unit must communi

-

cate with.)

After changing the multicast 

port, you must send the Save 

command to make sure that the 

system uses this port at next 

reboot.

MULTICAST

-

PORT=<X>

0-65555

7979

R/W

 

Example of use: NEUNIT=1,SETTINGS=LAN,IPADDRESS=192.168.10.2,SUB

-

NET=255.255.255.0,GATEWAY=192.168.10.1\CR

Содержание 2:25





























Отзывы: