FlexPAK
Error
Possible cause
Solution
• Problem with (PS) cable
• DIR_time settings
If the unit does not go into Idling mode and filter clean-
ing does not take place after 10 seconds, break the PS
cable manually by opening fuse holder F4. Wait at least
10 seconds. If switching to Idling mode occurs this time,
troubleshoot the PS cable. If switching does not occur,
check the time set on the display (DIR_time function).
The compressed air pressure or
flow is too low.
• Adjust the pressure.
• Check the hose dimension
The solenoid valve is not connec-
ted properly.
Check the valve and air pressure.
The air lines, valve and/or cylinder
are blocked.
• Clean or replace the air lines, valve and/or cylinder.
• Filter incoming compressed air.
The cylinder and/or valve does
not work.
Replace the cylinder and/or valve.
Dust is hard to clean, normal
cleaning does not work.
Contact your nearest authorized distributor or Nederman
for technical advice.
Filter cleaning does
not work.
The cleaning interval is too short.
Extend the cleaning interval.
Compressed air, (Pr/t)
is <1 bar.
pressure can result in premature filter clogging. If the pres-
sure is lacking or too low, the piston cannot open the FCV
and lid properly. This results in insufficient cleaning and
premature filter clogging.
The CAS is connected to terminals X1:15 and X1:16. If no
CAS is installed, a jumper is linking the terminals to ensure
that the CAS message is not displayed in PLC Logo!.
Filter cleaning does not work.
No dust is collected in
the collector bin.
Insignificant flow to the unit.
See ‘Low vacuum or air flow’.
8 Spare Parts
CAUTION! Risk of equipment damage
Use only N
$
e
$
d
$
e
$
r
$
m
$
a
$
n
$
original spare parts and ac-
cessories.
Contact your nearest authorized distributor or
N
$
e
$
d
$
e
$
r
$
m
$
a
$
n
$
for advice on technical service or
if you require help with spare parts. See also
w
$
w
$
w
$
.
$
n
$
e
$
d
$
e
$
r
$
m
$
a
$
n
$
.
$
c
$
o
$
m
$
.
8.1 Ordering spare parts
When ordering spare parts always state the following:
• The part number and control number (see the
product identification plate).
• Detail number and name of the spare part (see
w
$
w
$
w
$
.
$
n
$
e
$
d
$
e
$
r
$
m
$
a
$
n
$
.
$
c
$
o
$
m
$
/
$
e
$
n
$
/
$
s
$
e
$
r
$
v
$
i
$
c
$
e
$
/
$
s
$
p
$
a
$
r
$
e
$
-
$
p
$
a
$
r
$
t
$
-
$
s
$
e
$
a
$
r
$
c
$
h
$
).
• Quantity of the parts required.
9 Recycling
The product has been designed for component mater-
ials to be recycled. Different material types must be
handled according to relevant local regulations. Con-
tact the distributor or
$
N
$
e
$
d
$
e
$
r
$
m
$
a
$
n
$
if uncertainties arise
when scrapping the product at the end of its service
life.
9.1 Environmental information
The following environmental information is valid for
FlexPAK:
• Cadmium-free and halogen-free relays in the control
equipment.
• Solvent-free washing and lacquer.
• 93,6% recyclable.
27
Содержание FlexPAK Standard
