background image

FlexPAK

NOTE! 
• Contact Nederman if the frequency convert-

er needs service.

• The unit is CE-marked. Connections to the

unit, initial start-up and maintenance are
to be carried out according to the product
manuals.

6.1 Checks one month after installation
and every year

WARNING! Risk of electric shock
Always disconnect the supply voltage with
the maintenance switch before any service,
whether mechanical or electrical. Always lock
the maintenance switch in the off position. Do
not use the emergency stop button as a substi-
tute.

WARNING! Risk of personal injury
• Ensure that there is no vacuum present in the

system during service.

• Always disconnect the compressed air supply

before any service.

NOTE! 
Check all power conductors and protective con-
ductors one month after installation and tight-
en, if required, to ensure good contact. Service
to the electrical equipment may only be carried
out by a qualified electrician.

One month after installation, and then every year,
perform the following checks:
• Check all power and protective conductors and

ground wire connections. Tighten, if required, to en-
sure good contact.

• Inspect the integrity of the dust separator.
• Ensure that the inside of the unit and the connec-

tion ducts are free from deposits. A build-up of de-
posits inside the duct system may cause the dis-
charge of static electricity.

• Inspect valves, hoses and seals for leakage.
• Clean the area around the unit and all areas where

the collected material is stored to ensure that there
are no dust deposits.

• Check that all signs/markings regarding safe opera-

tion are in place and that the personnel knows about
them.

• Verify the function of all emergency stop buttons,

alarms and signalling devices.

6.2 Empty the collector bin

WARNING! Explosion risk
Never use the unit without a bag.

WARNING! Risk of personal injury
• Ensure that there is no vacuum in the dust

separator before removing the collector bin.

• Crush hazard. Be careful when lowering and

refitting the collector bin. Use proper pro-
tective equipment.

• Wear goggles, a dust mask and gloves when

emptying the collector bin.

CAUTION! Risk of equipment damage
Use only Nederman original spare parts and ac-
cessories.

NOTE! 
The plastic bag is to be replaced when filled up
to 2/3, see 

Figure 11

.

6.3 Replace the plastic bag

1

Check that the risk area is clear.

2

Ensure that there is no vacuum in the dust separ-
ator.

3

Remove the collector bin.

4

Seal and remove the plastic bag. Use a cable tie or
equivalent, see 

Figure 12

.

5

Fit a new plastic bag in the collector bin, see 

Fig-

ure 13

.

6

Refit the collector bin onto the dust separator.

7

Check that the pressure equalizer hose is attached
to the collector bin, see 

Figure 14

.

8

Check that the collector bin seals properly once
the vacuum is re-applied to the dust separator.

6.4 Replace the main filter

WARNING! Risk of personal injury
• The electricity, vacuum and compressed air

to the unit must be turned off before com-
mencing filter change.

• This is a two person job. Use proper protect-

ive equipment.

• Don’t move under suspended tilted filter and

housing.

• Waste material collected in FlexPAK can con-

stitute a health risk. Always check the safety
requirements related to the specific waste
when handled.

• Perform a filter cleaning and wait for the dust

to settle, then empty and refit the collector
bin before replacing the filter.

• The used filter should be extracted into- and

stored in a plastic bag to minimize the spread
of filter contents.

22

Содержание FlexPAK Standard



































Отзывы: