Nedap TRANSIT Entry Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 30

background image

TRANSIT ENTRY | INSTALLATION GUIDE

FCC / IC Statement

28/30

C

FCC / IC STATEMENT

FCC ID: CGD-TRANSITENTRY
IC: 1444A-TRANSITE

This device complies with part 15 of the FCC Rules and to RSS210 of Industry
Canada. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.

«
...
26
27
28
29
30
»

Содержание TRANSIT Entry































Отзывы:

Нет отзывов

Похожие инструкции для TRANSIT Entry

PACSystems RX7i

Бренд: GE Страницы: 317

Бренд: rav Страницы: 120

Бренд: Lathem Страницы: 4

Бренд: texet Страницы: 28

Бренд: Quickie Страницы: 108

Бренд: Crosby Страницы: 8

Бренд: Ruida Technology Страницы: 35

Бренд: Zennio Страницы: 2

Бренд: Daewoo Страницы: 44

Бренд: Automated Logic Страницы: 3

Бренд: BHM Medical Страницы: 56

THERMASGARD 9112

Бренд: S+S Regeltechnik Страницы: 48

Бренд: ICP DAS USA Страницы: 82

Бренд: WilTec Страницы: 4

Бренд: Pronomic Страницы: 20

Бренд: Brew Monk Страницы: 134

Бренд: Braun Страницы: 41

Бренд: SeaLevel Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды