background image

TRANSIT ENTRY | INSTALLATION GUIDE 

Firmware Upgrade

 

 

25/30 

9

 

FIRMWARE UPGRADE 

The firmware in the TRANSIT Entry’s processor can be upgraded by means of the 
serial interface (RS232, RS422 or USB). The upgrade is performed by the ‘PIC 
downloader’ application. The upgrade procedure is described below. 
 

1

 

Start the ‘PIC downloader’ application. 

2

 

Select the serial port to which the reader is connected. 

3

 

Select the firmware file (*.hex, *.ehx). 

4

 

Disable ‘download customer codes’ to prevent your customer codes inside 
the reader to be overwritten. Enable ‘download customer codes’ when you 
want to load the customer codes from the hex-file into the reader. Hex-files 
on 

www.nedapidentification.com

 contain DEMO customer codes.  

5

 

Click ‘Download’ to start downloading the firmware. 

6

 

Once the downloading has completed ‘PIC downloader’ displays the 
message ‘Download successfully completed’ and the reader starts the 
upgraded firmware. 

 

 

Figure 25: PIC downloader 

Note 

 

Aborted downloads may 
cause the reader to stop 
functioning. In such cases 
repeat the upgrade 
procedure until it succeeds. 
 

Note 

If the message ‘Searching 
for bootloader’ does not 
disappear check the cables 
and the com-port settings. 
Sometimes it may be 
required to restart the 
reader before the 
bootloader can be found. 
Before restarting the reader 
make sure that the message 
‘Searching for bootloader’ is 
still shown in the statusbar. 
The restart is easily 
performed by pressing the 
reset-switch. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание TRANSIT Entry































Отзывы: