Necta Necta Colibri Espresso, Инструкция по установке, эксплуатации и обслуживанию

Страница: 21 / 47

18
© by NECTA VENDING SOLUTIONS SpA 09-2003 228 00
LIQUID WASTE FULL
If the machine is equipped with a liquid waste container
(housed in the cabinet) fitted with an overflow warning
device, the machine locks.
WATER FAILURE
Models with water supply from the mains / without
support cabinet
The machine locks if the air-break microswitch is closed
for more than 10 seconds. When pressing a selection
button the water inlet solenoid valve is triggered to check
the water flow from the mains. If the failure is not reset
automatically, it will be necessary to restart the machine
to be able to reset the failure again by pressing a selection
button.
CHANGER FAILURE (MDB only)
The change-giver coin mechanism is not working or does
not communicate.
BILL VALIDATOR FAILURE (MDB only)
The bill accepter is not working or does not communicate.
CASHLESS FAILURE (MDB only)
The key device or the magnetic card is not working or does
not communicate.
PROGRAMMING THE
WATER AND POWDER DOSES
When either the “Water doses” or the “Powder doses”
functions from the “programming” menu are displayed the
related doses can be changed.
The various doses are identified by dose codes, which are
displayed each time.
The dose code locates the water and powder doses related
to a given selection; any changes to one selection dose
also affects the compound selections where the dose
code is used.
Refer to the selection dose table for the dose code list.
The values of the doses displayed are expressed in:
- tenths of a second for powders;
- number of pulses of the volumetric counter for water.
Press the confirm button “ ” from the “programming”
menu to access the dose code list, which can be scrolled
with the “ ” and “ ” buttons.
When pressing change button “ ”, this value will start
blinking and can be modified as necessary.
PRICE SETTING
When the “Set Prices” (price programming) function from
the “programming” menu is displayed, the 8 sales prices
stored can be changed.
The prices are indicated as number of basic coins.
Press the confirm button “ ” from the “programming”
menu to access the price list, which can be scrolled with
the “ ” and “ ” buttons.
When pressing change button “ ”, this value will start
blinking and can be modified as necessary.
PROGRAMMING THE PRICES
AND THE BUTTON STATUS
When the “Set Prices/Button” (price combination) func-
tion of the “programming” menu is displayed, the combi-
nation of the button to one of the stored prices and/or to
the status of a selection can be changed.
Press the confirm button “ ” from the “programming”
menu to access the price list, which can be scrolled with
the “ ” and “ ” buttons.
When pressing the change button “ ”, the selection status
starts blinking.
Using the “ ” and “ ” buttons, the selection status can be
changed from (enabled) to (disabled).
Press again the confirm button “ ” to display the price
number referred to in the price table.
When pressing change button “ ”, this value will start
blinking and can be modified as necessary.
The buttons which control pre-selections do not need
combination with prices. In any case prices have no effect
on the pre-selection buttons.
PROGRAMMING THE BASIC COIN AND
THE DECIMAL POINT
When the “Basic coin / DP” (basic coin value) function
from the “programming” menu is displayed, the value of
the basic coin as well as the position of the decimal point
can be modified.
Press the confirm button “ ” from the “programming”
menu to display the current value of the basic coin.
Using the “ ” and “ ” buttons, the value of the basic coin
and the number of the decimal point position “dP” are
displayed alternately, i.e:
0 decimal point disabled
1 XXX.X
2 XX.XX
3 X.XXX
Press the change button “ ”, these values will start
blinking and can then be modified as necessary.
PAYMENT SYSTEMS
When the “Payment system” function is displayed, it is
possible to define which payment system to use, selecting
among:
- Validator
- MDB communication protocol
In order to install payment systems different from a
validator special kits must be used.
The payment systems must be housed in the cabinet
(optional).