Anzeige-Zustand
Projektor-Zustand
Hinweis
Anzeige-Zustand
Projektor-Zustand
Hinweis
TDieses Kapitel hilft Ihnen bei der Beseitigung von Störungen, die bei der Einrichtung oder während des Betriebes
Ihres Projektors auftreten können.
Netzanzeige (POWER)
Anzeige-Zustand
Projektor-Zustand
Hinweis
Aus
0,5 sec ON,
0,5 sec OFF
2,5 sec ON,
0,5 sec OFF
0,5 sec ON,
0,5 sec OFF
Die Hauptstromversorgung ist
ausgeschaltet.
Der Projektor ist einschaltbereit.
Der Projektor befindet sich im
Einschlaf-Timer-modus.
Der Projektor befindet sich in der
Abkühlphase.
Der Projektor ist eingeschaltet.
Der Projektor befindet sich in
Betriebsbereitschaft oder Standby.
Grün
Orange
–
Warten Sie einen Moment.
–
Warten Sie einen Moment.
–
–
Aus
Normal
Lampenabdeckungsfehler
Spiegelabdeckungsfehler
Temperaturfehler
Temperaturfehler als Folge von
Staub
Spannungsfehler
Lüfterfehler
Lampenfehler
Neuaktivierung der Lampe
Die Tastensperre ist aktiviert
Eine Hand oder ein anderes Objekt
blockiert den Lichtkegel.
Gerät befindet sich in Betriebs-
bereitschaft
–
Tauschen Sie die Lampen-
abdeckung richtig aus.
Stellen Sie sicher, dass die Abdeckung
offen ist. Der Projektor kann mit
geschlossener Spiegelabdeckung nicht
eingeschaltet werden.
Der Projektor ist überhitzt. Bringen Sie
den Projektor an einen kühleren Ort.
Entfernen Sie den Staub im
Lichtkegel.
Das Netzgerät funktioniert nicht
richtig.
Die Lüfter funktionieren nicht
richtig.
Lampe leuchtet nicht. Warten Sie
eine volle Minute und dann wieder
einschalten.
Der Projektor aktiviert neu.
Sie haben bei aktivierter Tastensperre
eine Bedienfeldtaste gedrückt.
Entfernen Sie es aus dem
Lichtkegel.
–
Statusanzeige (STATUS)
Blinkendes Lämpchen
Anzeige leuchtet
Anzeige blinkt grün
Anzeige blinkt orange
Blinkendes Lämpchen
Anzeige leuchtet
Anzeige blinkt rot
Anzeige blinkt grün
Orange
Rot
Grün
1 Zyklus (0,5 sec ON,
2,5 sec OFF)
2 Zyklus (0,5 sec ON,
0,5 sec OFF)
3 Zyklus (0,5 sec ON,
0,5 sec OFF)
4 Zyklus (0,5 sec ON,
0,5 sec OFF)
6 Zyklus (0,5 sec ON,
0,5 sec OFF)
Aus
Normal
Die Lampe hat das Ende ihrer Lebensdauer erreicht. Die
Lampenaustausch-Meldung wird angezeigt.
Die zulässige Lampenbetriebsstundenzahl wurde
überschritten. Der Projektor schaltet sich erst nach dem
Austauschen der Lampe wieder ein.
Der Lampen-Modus ist auf Eco eingestellt.
Rot
Rot
Grün
–
Tauschen Sie die Lampe aus.
Tauschen Sie die Lampe aus.
–
Lampenanzeige (LAMP)
Blinkendes
LämpchenAnzeige
leuchtet
8. Fehlersuche
G-13