NEC T30A Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 252

background image

－

viii

－

Power Supply and Power Cord Use

Do not hold the power plug with a wet hand.

Do not disconnect/connect the plug while your hands are wet. Failure to follow this
warning may cause an electric shock.

Do not connect the ground wire to a gas pipe.

Never connect the ground wire to a gas pipe. Failure to follow this warning may cause a
gas explosion.

If you disconnect the power, disconnect the two power lines.

The product might be powered from 2 AC power lines. If you disconnect the power from
the device, both 2 power sources must be disconnected. It may cause an electric shock if
the power is not disconnected properly.

Plug in to a proper power source.

Use a proper wall outlet. Use of an improper power source may cause a fire or a power
leak. Do not install the product where you need an extension cord. Use of a cord that does
not meet the power specifications of the product may heat up the cord and cause a fire.

Do not connect the power cord to an outlet that has an illegal number of
connections.

The electric current exceeding the rated flow overheats the outlet, which may cause a fire.

Insert the power plug into the outlet as far as it goes.

Heat generation resulting from a halfway inserted power plug (imperfect contact) may
cause a fire. Heat will also be generated if condensation is formed on dusty blades of the
halfway inserted plug, increasing the possibility of fire.

Do not use the attached power cord for any other devices or usage.

The power cord that comes with your product is designed aiming to connect with this
product and to use with the product, and its safety has been tested. Do not use the attached
power cord for any other purpose. Doing so may cause a fire or an electric shock.

«
...
7
8
9
10
11
...
»

Содержание T30A





























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для T30A

Бренд: IBM Страницы: 80

Spinpiont HD320KJ

Бренд: Samsung Страницы: 1

Бренд: Stardom Страницы: 2

Бренд: Keter Страницы: 76

TotalStorage DS4200

Бренд: IBM Страницы: 222

Бренд: Seagate Страницы: 2

Бренд: IBM Страницы: 2

B. spaces Tidy Toybox

Бренд: Maison Battat Страницы: 2

Бренд: Fast Mover Страницы: 2

Бренд: U-Line Страницы: 3

Бренд: JOBO Страницы: 20

Бренд: HGST Страницы: 51

Storage 6180 Array

Бренд: Oracle Страницы: 6

StorageTek SL3000

Бренд: Oracle Страницы: 216

Pillar Axiom 600

Бренд: Oracle Страницы: 229

Бренд: Argosy Страницы: 1

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды