manualshive.com logo in svg
background image

English-25

English

Specifications - MD212MC

Monitor Specifications

MD212MC Monitor

Notes

LCD Module

Diagonal:

54.0 cm/21.3 inches

Active matrix; thin film transistor (TFT)

Viewable Image Size:

54.0 cm/21.3 inches

liquid crystal display (LCD); UA - SFT (IPS);

Native Resolution (Pixel Count):

1200 x 1600 (Portrait)

0.27 mm dot pitch; 850 cd/m

2

 max

1600 x 1200 (Landscape)

luminance, 400 cd/m

2

 calibrated luminance;

1050:1 contrast ratio, typical.

Input Signal

Video:

ANALOG 0.7 Vp-p/75 Ohms

Digital Input: DVI

Sync:

Separate sync.TTL Level
Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Composite sync. Positive/Negative

Display Colors

16,777,216

Depends on display controller used.

Synchronization Range

Horizontal:

31.5 kHz to 91.1 kHz

Automatically

Vertical:

50.0 Hz to 85 Hz

Automatically

Clock Frequency

162 MHz

Viewing Angle

Left/Right:

±88° (CR > 10)

Up/Down:

±88° (CR > 10)

Image Formation Time

35 ms (Typ.)

20 ms (Gray to gray, typical)

Resolutions Supported

640 x 480*

1

 at 60 Hz to 85 Hz

(Some systems may not support

720 x 400*

1

 at 70 Hz to 85 Hz

all modes listed).

800 x 600*

1

 at 56 Hz to 85 Hz

832 x 624*

1

 at 75 Hz

1024 x 768*

1

 at 60 Hz to 85 Hz

1152 x 864*

1

 at 70HZ to 85Hz

1152 x 870*

1

 at 75Hz

1280 x 960*

1

 at 60 Hz

1280 x 1024*

1

 at 60 Hz to 85 Hz

1400 x 1050*

1

 at 60 Hz to 75 Hz

NEC DISPLAY SOLUTIONS cites

1440 x 900*

1

 at 60 Hz to 75 Hz

recommended resolution for optimal

1600 x 1200*

1

 at 60 Hz................................... display performance.

Active

Landscape:

Horiz.: 432 mm/17.0 inches

Vert.: 324 mm/12.8 inches

Display Area

Portrait:

Horiz.: 324 mm/12.8 inches

Vert.: 432 mm/17.0 inches

Power Supply

AC 100-240 V ~ 50/60 Hz

Current Rating

1.6 - 0.7 A

For Mexico 2.0A

Dimensions

Landscape:

467.8 mm (W) x 434.3 - 584.3 mm (H) x 306 mm (D)
18.4 inches (W) x 17.1 - 23.0 inches (H) x 12.0 inches (D)

Portrait:

361.6 mm (W) x 487.4 - 637.4 mm (H) x 306 mm (D)
14.2 inches (W) x 19.2 - 25.1 inches (H) x 12.0 inches (D)

Height Adjustment:

150 mm / 5.9 inches

Weight

10.7 kg (23.5 lbs)

Environmental Considerations

Operating Temperature:

5°C to 35°C/41°F to 95°F

Humidity:

30% to 80%

Altitude:

-1,246 to 9,842 Feet/-380 to 3,000 m

Atmospheric pressure:

700hPa to 1060hPa

Transport/Storage Temperature:

-10°C to 60°C/14°F to 140°F

Humidity:

10% to 85%

Altitude:

-1,246 to 40,000 Feet/-380 to 12,192 m

Atmospheric pressure:

200hPa to 1060hPa

*1 Interpolated Resolutions: When resolutions are shown that are lower than the pixel count of the LCD module, text may appear different. This is normal and
necessary for all current flat panel technologies when displaying non-native resolutions full screen. In flat panel technologies, each dot on the screen is actually
one pixel, so to expand resolutions to full screen, an interpolation of the resolution must be done.

NOTE: 

Technical specifications are subject to change without notice.

Содержание MD213MC - MultiSync - 21.3" LCD Monitor

































Отзывы: