E – 38
Communication Speed:
This feature sets the baud rate of the PC Control port (Mini DIN 8 Pin).
It supports data rates from 4800 to 38400 bps.
The default is 38400 bps. Select the appropriate baud rate for your
equipment to be connected (depending on the equipment, a lower
baud rate may be recommended for long cable runs).
Default Source Select:
You can set the projector to default to any one of its inputs each
time the projector is turned on.
Last .............. Sets the projector to default to the previous or last active
input each time the projector is turned on.
Auto ............. Searches for an active source in order of RGB*
→
Video
→
S-Video
→
PC Card Viewer
→
RGB and displays the first
found source.
Select ........... Displays the selected source input every time the projector is
started up. Select an input from the pull-down menu.
* "DVI (DIGITAL)
→
DVI (ANALOG)" on LT158.
Control Panel Key Lock:
This option turns on or off the Control Panel Key Lock function.
NOTE:
* This Control Panel Key Lock does not affect the remote control and the PC
Control functions.
* When the cabinet buttons are disabled, pressing and holding the CANCEL
button for about 10 seconds will change the setting to enabled.
[Page5]
[Page4]
Auto Adjust (RGB Only):
When "Auto Adjust" is set to "On", the projector automatically de-
termines the best resolution for the current RGB input signal to
project an image using NEC's Advanced AccuBlend Intelligent Pixel
Blending Technology.
The image can be automatically adjusted for position and stability;
"Horizontal Position", "Vertical Position", "Clock"
and
"Phase
.
"
On ................ Automatically adjusts image "Horizontal Position", "Vertical
Position", "Clock" and "Phase".
Off ................ User can adjust the image display functions ("Horizontal Po-
sition", "Vertical Position", "Clock" and "Phase") manually.
NOTE: For LT158
This feature is not available for DVI (DIGITAL) signal.
If you make any adjustment to DVI digital signal, the Auto Adjust feature
automatically adjusts position and stability; Horizontal and Vertical Posi-
tion, and Resolution. However, the horizontal and vertical adjustments will
not be stored in memory.
Auto Start:
Turns the projector on automatically when the power cable is inserted
into an active power outlet. This eliminates the need to always use
the "Power" button on the remote control or projector cabinet.
Power Management:
When this option is on and there is no RGB input for five minutes or
more, the projector will automatically turn itself off.
Power Off Confirmation:
This option determines whether a confirmation dialog for turning off
the projector will appear or not.
NOTE:
When the confirmation message is displayed, you must be in the
Projector mode to operate your projector using the remote control. If not,
press the PJ button on the remote control to change your projector to the
Projector mode. The button lights to indicate that you are in the Projector
mode.
Keystone Save:
This option enables you to save your current keystone settings.
Saving your change once affects all sources. The changes are saved
when you turn off the projector.
Clear Lamp Hour Meter:
Resets the lamp clock back to zero. Pressing this button appears a
confirmation dialog box. To reset the lamp usage hour, press "OK".
NOTE:
The projector will turn off and go into standby mode after 1600 hours
(up to 2600 hours in Eco mode) of service. If this happens, press the "Help"
button on the remote control for ten seconds to reset the lamp clock back
to zero. Do this only after replacing the lamp.
Clear Filter Usage:
Resets the filter usage back to zero. Pressing this button appears a
confirmation dialog box. To reset the filter usage hour, press "OK".
Содержание LT157 - XGA LCD Projector
Страница 1: ...LCD Projector LT158 LT157 User s Manual ...
Страница 61: ...Printed in Japan 7N8P1211 ...
