NEC IE-784225-NS-EM1 Скачать руководство пользователя страница 20

Страница: 20 / 51

CHAPTER 3 INSTALLATION

User’s Manual U13742EJ2V0UM

3.2

Target Device Setting

SW1 in the IE-784225-NS-EM1 must be set in accordance with the target device (the

PD784216A, 784216AY,

784218A, 784218AY, or 784225 Subseries) as follows.

PD784216A, 784218A Subseries:

Set SW1 to the 3, 6 pin side

PD784225 Subseries:

Set SW1 to the 1, 4 pin side

3.3

Selection of Emulator Main Unit

SW2 in the IE-784225-NS-EM1 must be set in accordance with the emulator main unit to be used as follows.

Using IE-784225-NS-EM1 in combination with IE-78K4-NS: Set SW2 to the 3, 6 pin side (shipment setting)

Using IE-784000-R in combination with IE-784225-NS-EM1 and IE-78K4-R-EX2: Set SW2 to the 1, 4 pin side

3.4

Clock Settings

3.4.1 Overview of clock settings

The main system and subsystem clocks to be used during debugging can be selected from (1) to (3) below.

(1) Clock that is already mounted on emulation board

(2) Clock that is mounted by user

(3) External clock

If the target system includes an internal clock, select either “(1) Clock that is already mounted on emulation board”

or “(2) Clock that is mounted by user”. For an internal clock, the target device is connected to a resonator and the

target device’s internal oscillator is used. An example of the external circuit is shown in part (a) of Figure 3-2. During

emulation, the resonator that is mounted on the target system is not used. Instead, it uses the clock that is mounted

on the emulation board, which is installed for the IE-78K4-NS.

If the target system includes an external clock, select “(3) External clock”.

For an external clock, a clock signal is supplied from outside of the target device and the target device’s internal

oscillator is not used. An example of the external circuit is shown in part (b) of Figure 3-2.

Figure 3-2. External Circuits Used as System Clock Oscillator

(a) Internal clock

(b) External clock

X2 or XT2

Target device

External
clock

X1 or XT1

Содержание IE-784225-NS-EM1




















































Результаты поиска

Содержание IE-784225-NS-EM1

Отзывы:

Похожие инструкции для IE-784225-NS-EM1

Бренды по названию

Популярные бренды

NEC IE-784225-NS-EM1, Руководство пользователя

Результаты поиска

Содержание IE-784225-NS-EM1

Отзывы:

Похожие инструкции для IE-784225-NS-EM1

Бренды по названию

Популярные бренды